Wiki source code of BMS Main X
Hide last authors
| author | version | line-number | content |
|---|---|---|---|
 |
5.1 | 1 | (% class="box infomessage" %) |
| 2 | ((( | ||
| 3 | BMS Main X firmware update procedure is described [[here>>doc:Battery management systems.BMS Main X.5\. Firmware update.WebHome]]. | ||
| 4 | ))) | ||
| 5 | |||
| |
4.1 | 6 | = v2.6.3 = |
| 7 | |||
| 8 | [[BMS_Main_X2_v2.6.3.srec>>FileManager.BMS_Main_X2_v2\.6\.3\.srec]] | ||
| 9 | |||
| 10 | == Improvements == | ||
| 11 | |||
| 12 | * adaptation of the device to the production test bench | ||
| 13 | |||
| |
3.1 | 14 | = v2.6.2 = |
| 15 | |||
| 16 | [[BMS_Main_X2_v2.6.2.srec>>FileManager.BMS_Main_X2_v2\.6\.2\.srec]] | ||
| 17 | |||
| 18 | == Fixes == | ||
| 19 | |||
| 20 | * resolving the problem of saving device parameters | ||
| 21 | |||
| 22 | = v2.6.1 = | ||
| 23 | |||
| 24 | [[BMS_Main_X2_v2.6.1.srec>>FileManager.BMS_Main_X2_v2\.6\.1\.srec]] | ||
| 25 | |||
| 26 | == Fixes == | ||
| 27 | |||
| 28 | * resolving the issue of preparing battery module states written to Modbus registers | ||
| 29 | * resolving the problem of writing the device's working time to a non-volatile memory very often | ||
| 30 | * resolving the problem of returning error states when saving device parameters (mainly via Wi-Fi) | ||
| 31 | |||
| |
1.2 | 32 | = v2.6.0 = |
| 33 | |||
| 34 | [[BMS_Main_X2_v2.6.0.srec>>FileManager.BMS_Main_X2_v2\.6\.0\.srec]] | ||
| 35 | |||
| 36 | == Features == | ||
| 37 | |||
| 38 | * new parameter to set the minimum number of battery modules allowed to join (see the "Control - Charge" and "Control - Discharge" sections) | ||
| 39 | * ability to rejoin battery modules if their voltage is close to the battery voltage (see the "Control - Charge" and "Control - Discharge" sections) | ||
| 40 | * selection of errors that cause reset of contactor control signals (see the "Control - Main contactor", "Control - Charge", "Control - Discharge", "Control - Heater", "Control - Cooler" sections) | ||
| 41 | * new internal signal "General error (modules)" which is the logical sum of the "General error" signals from the battery modules | ||
| 42 | * new assignments "Charging", "Precharging", "Discharging", "Charging/Discharging", "Main contactor", "Critical error" and "General error (modules)" for the discrete outputs (see the "Signals - Output discrete signals - Assignments" section) | ||
| 43 | * new assignments "Critical error" and "General error (modules)" for the relays (see the "Signals - Relays - Assignments" section) | ||
| 44 | |||
| |
2.1 | 45 | == Improvements == |
| |
1.2 | 46 | |
| |
2.1 | 47 | * rearrangements in the settings sections, which are made to simplify the setup process |
| 48 | |||
| 49 | == Fixes == | ||
| 50 | |||
| 51 | * resolving the problem of device hanging due to high activity on the CAN bus during startup |