Changes for page 3.3 Control

Last modified by Admin on 2025/08/11 17:07

From 30.1 to 29.1 From 37.1 to 36.2

From version 36.2

edited by Admin
on 2025/08/11 17:01

Change comment: There is no comment for this version

To version 30.1

edited by Admin
on 2025/02/24 13:49

Change comment: Загрузить новое вложение 1740404973346-344.png

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)
Attachments (0 modified, 0 added, 3 removed)

Details

Page properties

Content

@@ -208,11 +208,11 @@
  * Enable – a flag to start calculation of the charge current limit;
  * Maximum charge current – a maximum allowable value of the charge current (under normal conditions), A;
  * Rate of change – a rate of change the current limit to a new value (0 is for immediate change), A/s;
--* Option 1: Limit charge current by the battery SOC and temperature – a flag to enable correction of maximum allowable charging current** Kcs** depending on __maximum cell SOC__ and battery temperature;
++* Option 1: Limit charge current by the battery SOC and temperature – a flag to enable correction of maximum allowable charging current** Kcs** depending on SOC and battery temperature;
  * Option 1: SOC x Temperature x Factor – the dependence of the correction factor on SOC and battery temperature;
  * Option 2: Limit charge current by the contactor temperature – a flag to enable correction of maximum allowable charging current **Kcc** depending on contactor temperature;
  * Option 2: Contactor temperature x Factor – the dependence of the correction factor on SOC and contactor temperature;
--* Option 3: Limit charge current by the maximum cell voltage - a flag to enable correction of maximum allowable charging current **Kcv** depending on __the maximum cell U,,ocv,, voltage__ (corrected due to current and cell resistance)
++* Option 3: Limit charge current by the maximum cell voltage - a flag to enable correction of maximum allowable charging current **Kcv** depending on maximum cell voltage;
  * Option 3: Cell voltage x Factor – the dependence of the correction factor on maximum cell voltage;
  * Option 4: Limit charge current by the cell temperature - a flag to enable correction of maximum allowable charging current **Kct** depending on maximum cell temperature;
  * Option 4: Cell temperature x Factor – the dependence of the correction factor on maximum cell temperature.
@@ -236,11 +236,11 @@
  * Enable – a flag to start calculation of the discharge current limit;
  * Maximum discharge current – a maximum allowable value of the discharge current (under normal conditions), A;
  * Rate of change – a rate of change the current limit to a new value (0 is for immediate change), A/s;
--* Option 1: Limit discharging current by the battery SOC and temperature – a flag to enable correction of maximum allowable discharging current **Kds **depending on __minimum cell SOC__ and temperature;
++* Option 1: Limit discharging current by the battery SOC and temperature – a flag to enable correction of maximum allowable discharging current **Kds **depending on SOC and temperature;
  * Option 1: SOC x Temperature x Factor – the dependence of the correction factor on SOC and battery temperature;
  * Option 2: Limit discharge current by the contactor temperature – a flag to enable correction of maximum allowable discharging current **Kdc** depending on contactor temperature;
  * Option 2: Contactor temperature x Factor – the dependence of the correction factor on SOC and contactor temperature;
--* Option 3: Limit discharge current by the cell voltage - a flag to enable correction of maximum allowable discharging current **Kdv** depending on __the minimum cell U,,ocv,, voltage__ (corrected due to current and cell resistance)
++* Option 3: Limit discharge current by the cell voltage - a flag to enable correction of maximum allowable discharging current **Kdv** depending on minimum cell voltage;
  * Option 3: Cell voltage x Factor – the dependence of the correction factor on minimum cell voltage;
  * Option 4: Limit discharge current by the cell temperature - a flag to enable correction of maximum allowable discharging current **Kdt** depending on maximum cell temperature;
  * Option 4: Cell voltage x Factor – the dependence of the correction factor on minimum cell temperature.
@@ -297,15 +297,13 @@
  To change the parameters of charging process status, select the "Control → Charging status" section:
--[[image:1754931617275-503.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="135" width="800"]]
++[[image:1740399071280-626.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="123" width="800"]]
  In this section:
  * Current to set the "Charging current present" – a current level to generate the "Charging current present" signal, A;
  * Current to clear the "Charging current present" – a current level to clear the "Charging current present" signal, A;
--* Use actual voltage to generate the "Ready to charge" signal – a flag to disable voltage correction for "Ready to charge" signal;
--* Use actual voltage to generate the "Ready to charge" signal if the current is negative – a flag to disable voltage correction for "Ready to charge" signal only at discharging current;
--* Voltage to clear the “Ready to charge” – a threshold U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if the voltage of any cell is above this level, the “Ready to charge” (hence, the “Allow charging”) signal is cleared;
--* Voltage to reset the “Ready to charge” – a tolerant U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if all cell voltages are below the tolerant level, the “Ready to charge” (hence, the “Allow charging”) signal is set;
++* Voltage to clear the “Ready to charge” – a threshold voltage level on the cell, V; if the voltage of any cell is above this level, the “Ready to charge” (hence, the “Allow charging”) signal is cleared;
++* Voltage to reset the “Ready to charge” – a tolerant voltage level on the cell, V; if all cell voltages are below the tolerant level, the “Ready to charge” (hence, the “Allow charging”) signal is set;
  * Delay before recharging – a time after which the previously opened the allow charging contactor closes again, minute; to disable the operation by timeout set "Delay before recharging" to 0;
  * Errors 1, 2 to clear the "Ready to charge" – bitfields to choose the errors which will clear the "Ready to charge" signal.
@@ -320,13 +320,13 @@
  To change the parameters of discharging process status, select the "Control → Discharging status" section:
--[[image:1754931699901-802.png]]
++[[image:1740399096018-240.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="110" width="800"]]
  In this section:
  * Current to set the "Discharging current present" – a current level to generate the "Discharging current present" signal, А;
  * Current to clear the "Discharging current present" – a current level to clear the "Discharging current present" signal, А;
--* Voltage to clear the “Ready to discharge” – a threshold U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if the voltage of any cell is below this level, the “Ready to discharge” signal is cleared;
--* Voltage to reset the “Ready to discharge” – a tolerant U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if all cells voltages are above the tolerant level, the “Ready to discharge” signal is set;
++* Voltage to clear the “Ready to discharge” – a threshold voltage level on the cell, V; if the voltage of any cell is below this level, the “Ready to discharge” signal is cleared;
++* Voltage to reset the “Ready to discharge” – a tolerant voltage level on the cell, V; if all cells voltages are above the tolerant level, the “Ready to discharge” signal is set;
  * Errors 1, 2 to clear the "Ready to discharge" – bitfields to choose the errors which will clear the "Ready to discharge" signal.
  === Precharge ===
@@ -539,35 +539,27 @@
  === Cell balancing ===
--Balancing makes the voltage of all cells equal to the minimum cell voltage.
++Balancing makes the voltage of all cells be equal to the minimum cell voltage.
  The following balancing rules are supported:
--* when the battery is charging (current I > 0) and time after until the battery is relaxed;
++* only when the battery is charging (current I > 0) and some time until the battery is relaxed;
  * when the battery is charging (current I > 0) or when the battery is in a state of relaxation;
  * always (regardless of battery state).
--A balancing resistor is connected to the cell if the following conditions are simultaneously met:
++A balancing resistor is connected to the cell if:
--* the voltage on the cell is higher than the balancing start voltage;
--* the difference between the voltage on the cell and the minimum voltage among the battery cells is greater than the balancing start threshold;
++* the voltage on the cell is higher than the starting voltage of the balancing;
++* the difference between the cell voltage and the minimum voltage among the cells of the battery is greater than the balancing deviation.
--A balancing resistor is disconnected from the cell if any of the following conditions are met:
--
--* the voltage on the cell is less than the balancing stop voltage;
--* the difference between the voltage on the cell and the minimum voltage among the battery cells is less than the balancing stop threshold.
--
  (% class="box infomessage" %)
  (((
--If the “High logic temperature” occurs, then the balancing of the cells connected to the overheated BMS Logic device will not be performed.
++If the BMS Mini overheats, then the balancing of the cells connected to this device will not be performed.
  )))
--The BMS Mini device can enable the cell balancing by the external “Balancing request” signal. Balancing process will be started to cells which the voltage is higher than the balancing start voltage and the difference between the cell voltage and the minimum voltage among all the cells is greater than the balancing stop threshold.
--
--BMS Mini device can force a cell balancing, if its voltage is higher than estimated value.
--
  To change the cell balancing parameters, select the "Control → Cell balancing" section:
++
  [[image:1740404562825-676.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="168" width="800"]]
  In this section:
@@ -576,15 +576,11 @@
  ** Balance on charge;
  ** Balance on charge or relaxed;
  ** Balance always;
--* Balancing condition:
--** Automatic – balancing will be performed automatically if needed conditions are met;
--** On balancing request – balancing will start only if a remote request is received. In this case cells will start to balance regardless the "Voltage deviation to start balancing" value;
++
++[[image:1733746797004-660.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="104" width="800"]]
++
  * Minimum cell voltage to start balancing, V;
--* Voltage deviation to start balancing;
--* Voltage deviation to stop balancing;
--* Voltage for forced balancing – if cell voltage is above this value, it will start discharging through balancing resistor;
--* Maximum allowable temperature of the board, ºC;
--* Command to discharge all cells – a flag to force the balancing of all cells.
++* Balancing deviation, V.
  === Power down ===
@@ -599,20 +599,20 @@
  To change the parameters of the power down control, select the "Control → Power down" section:
--[[image:1740404859367-943.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="130" width="800"]]
++[[image:1733746797005-459.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="115" width="800"]]
++
  In this section:
  * Minimum voltage to power down – a minimum voltage level of the battery below which the BMS commands to shut down the battery, V;
  * Idle time to power down – a time of battery inactivity after which the battery is shut down, minute;
--* Wait the "Power up/down request" is cleared (on startup) – a flag to enable delay for clearing the “Power up/down request” signal while starting the BMS;
--* Delay before setting the internal power down signal – a delay before turning off the device power when receiving the “Power down request” command, ms.
++* Wait the "Power up/down request" is cleared (on startup) – a flag to enable delay for clearing the “Power up/down request” signal while starting the BMS.
  === Heater ===
  To change the parameters of the heater control algorithm, select the "Control → Heater" section:
++[[image:1733746808496-606.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="116" width="800"]]
--[[image:1740404973346-344.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="138" width="800"]]
  In this section:
  * Enable – a flag to enable heater control;
@@ -620,7 +620,7 @@
  * Tolerant cell temperature, °C;
  * Delay before starting the heater, millisecond;
  * Delay before stopping the heater, millisecond;
--* Errors 1, 2 to turn off the heater – bitfields to choose the errors which will turn off the heater.
++* Switch off the heater on errors (Undervoltage, Overcurrent, High temperature, Short circuit or Critical error).
  As a result of operating the heating algorithm, the “Heater” signal is generated.
@@ -641,8 +641,8 @@
  To change the parameters of the cooler control algorithm, select the "Control → Cooler" section:
++[[image:1733746808497-424.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="113" width="800"]]
--[[image:1740405145695-704.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="149" width="800"]]
  In this section:
  * Enable – a flag to enable cooler control;
@@ -650,7 +650,7 @@
  * Tolerant cell temperature, °C;
  * Delay before starting the cooler, millisecond;
  * Delay before stopping the cooler, millisecond;
--* Errors 1, 2 to turn off the heater – bitfields to choose the errors which will turn off the cooler.
++* Switch off the cooler contactor on errors (Undervoltage, Overcurrent, Low temperature, Short circuit or Critical error).
  As a result of operating the cooling algorithm, the "Cooler" signal is generated.

1740405145695-704.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.admin

Size

...	...	@@ -1,1 +1,0 @@
1		-20.6 KB

Content

1754931617275-503.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.admin

Size

...	...	@@ -1,1 +1,0 @@
1		-28.8 KB

Content

1754931699901-802.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.admin

Size

...	...	@@ -1,1 +1,0 @@
1		-30.3 KB

Content

Changes for page 3.3 Control

Summary

Details

Applications

Navigation

Table of Contents