Changes for page 3.3 Control

Last modified by Admin on 2025/04/09 12:15

From 29.1 to 28.2 From 30.3 to 30.2

From version 30.2

edited by Admin
on 2025/02/24 13:51

Change comment: There is no comment for this version

To version 29.1

edited by Admin
on 2025/02/24 13:47

Change comment: Загрузить новое вложение 1740404859367-943.png

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)
Attachments (0 modified, 0 added, 1 removed)
- 1740404973346-344.png

Details

Page properties

Content

@@ -537,35 +537,27 @@
  === Cell balancing ===
--Balancing makes the voltage of all cells equal to the minimum cell voltage.
++Balancing makes the voltage of all cells be equal to the minimum cell voltage.
  The following balancing rules are supported:
--* when the battery is charging (current I > 0) and time after until the battery is relaxed;
++* only when the battery is charging (current I > 0) and some time until the battery is relaxed;
  * when the battery is charging (current I > 0) or when the battery is in a state of relaxation;
  * always (regardless of battery state).
--A balancing resistor is connected to the cell if the following conditions are simultaneously met:
++A balancing resistor is connected to the cell if:
--* the voltage on the cell is higher than the balancing start voltage;
--* the difference between the voltage on the cell and the minimum voltage among the battery cells is greater than the balancing start threshold;
++* the voltage on the cell is higher than the starting voltage of the balancing;
++* the difference between the cell voltage and the minimum voltage among the cells of the battery is greater than the balancing deviation.
--A balancing resistor is disconnected from the cell if any of the following conditions are met:
--
--* the voltage on the cell is less than the balancing stop voltage;
--* the difference between the voltage on the cell and the minimum voltage among the battery cells is less than the balancing stop threshold.
--
  (% class="box infomessage" %)
  (((
--If the “High logic temperature” occurs, then the balancing of the cells connected to the overheated BMS Logic device will not be performed.
++If the BMS Mini overheats, then the balancing of the cells connected to this device will not be performed.
  )))
--The BMS Mini device can enable the cell balancing by the external “Balancing request” signal. Balancing process will be started to cells which the voltage is higher than the balancing start voltage and the difference between the cell voltage and the minimum voltage among all the cells is greater than the balancing stop threshold.
--
--BMS Mini device can force a cell balancing, if its voltage is higher than estimated value.
--
  To change the cell balancing parameters, select the "Control → Cell balancing" section:
++
  [[image:1740404562825-676.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="168" width="800"]]
  In this section:
@@ -574,15 +574,11 @@
  ** Balance on charge;
  ** Balance on charge or relaxed;
  ** Balance always;
--* Balancing condition:
--** Automatic – balancing will be performed automatically if needed conditions are met;
--** On balancing request – balancing will start only if a remote request is received. In this case cells will start to balance regardless the "Voltage deviation to start balancing" value;
++
++[[image:1733746797004-660.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="104" width="800"]]
++
  * Minimum cell voltage to start balancing, V;
--* Voltage deviation to start balancing;
--* Voltage deviation to stop balancing;
--* Voltage for forced balancing – if cell voltage is above this value, it will start discharging through balancing resistor;
--* Maximum allowable temperature of the board, ºC;
--* Command to discharge all cells – a flag to force the balancing of all cells.
++* Balancing deviation, V.
  === Power down ===
@@ -597,20 +597,20 @@
  To change the parameters of the power down control, select the "Control → Power down" section:
--[[image:1740404859367-943.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="130" width="800"]]
++[[image:1733746797005-459.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="115" width="800"]]
++
  In this section:
  * Minimum voltage to power down – a minimum voltage level of the battery below which the BMS commands to shut down the battery, V;
  * Idle time to power down – a time of battery inactivity after which the battery is shut down, minute;
--* Wait the "Power up/down request" is cleared (on startup) – a flag to enable delay for clearing the “Power up/down request” signal while starting the BMS;
--* Delay before setting the internal power down signal – a delay before turning off the device power when receiving the “Power down request” command, ms.
++* Wait the "Power up/down request" is cleared (on startup) – a flag to enable delay for clearing the “Power up/down request” signal while starting the BMS.
  === Heater ===
  To change the parameters of the heater control algorithm, select the "Control → Heater" section:
++[[image:1733746808496-606.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="116" width="800"]]
--[[image:1740404973346-344.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="138" width="800"]]
  In this section:
  * Enable – a flag to enable heater control;
@@ -618,7 +618,7 @@
  * Tolerant cell temperature, °C;
  * Delay before starting the heater, millisecond;
  * Delay before stopping the heater, millisecond;
--* Errors 1, 2 to turn off the heater – битовые поля для выбора ошибок, выключающих нагреватель.
++* Switch off the heater on errors (Undervoltage, Overcurrent, High temperature, Short circuit or Critical error).
  As a result of operating the heating algorithm, the “Heater” signal is generated.

1740404973346-344.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.admin

Size

...	...	@@ -1,1 +1,0 @@
1		-21.0 KB

Content

Changes for page 3.3 Control

Summary

Details

Applications

Navigation

Table of Contents