Skip to Content

Changes for page 3.3 Control

Last modified by Admin on 2025/04/09 12:15
From version 24.2
edited by Admin
on 2025/02/24 12:17
Change comment: There is no comment for this version
To version 25.1
edited by Admin
on 2025/02/24 12:23
Change comment: Загрузить новое вложение 1740399783613-216.png

Summary

Details

Page properties
Content
... ... @@ -406,23 +406,15 @@
406 406  ** Always on – charging is always allowed;
407 407  ** On charger connected – charging is allowed when there is a signal “Charger connected”;
408 408  ** On charge request – charging is allowed when there is a signal “Charge request”;
409 -* Current corresponding to charging – a current level to generate the "Charging current present" signal, A;
410 -* Current corresponding to no charging – a current level to clear the "Charging current present" signal, A;
409 +* Allow charging only when the "Ready to charge" signal is set – charging contactor will open if "Ready to charge" signal is cleared;
411 411  * Delay before starting charging – a time delay T,,on,, before closing the charging contactor and the allow charging contactor, millisecond;
412 412  * Delay before stopping charging – a time delay T,,off,, before opening the charging contactor, millisecond;
412 +* Control the precharging contactor – a flag that allows control of the precharging contactor (see [[Precharge>>url:http://#HPrecharge]]);
413 413  * Use custom delays before stopping charging (on errors) – a flag to enable manual settings of time delays T,,off,, for specific errors;
414 +* Errors 1, 2 to open the charging contactor – bitfields to choose the errors which will open the charging contactor;
414 414  * Custom delay: <error> – specific error delay, millisecond;
415 415  * Switch off the charging contactor on errors without delay – a flag to protectively open the charging contactor without a delay. In the opposite case, when an error is detected, the charging contactor opens always with the delay “Delay before stopping charging”;
416 -* Control the precharging contactor – a flag that allows control of the precharging contactor;
417 -* Voltage to clear the “Ready to charge” – a threshold voltage level on the cell, V; if the voltage of any cell is above this level, the “Ready to charge” (hence, the “Allow charging”) signal is cleared;
418 -* Voltage to reset the “Ready to charge” – a tolerant voltage level on the cell, V; if all cell voltages are below the tolerant level, the “Ready to charge” (hence, the “Allow charging”) signal is set;
419 -* Delay before recharging – a time after which the previously opened the allow charging contactor closes again, minute; to disable the operation by timeout set "Delay before recharging" to 0.
420 420  
421 -(% class="box infomessage" %)
422 -(((
423 -Note – The allow charging contactor closes under two independent conditions: 1) the voltage on the cells reaches the “Voltage to reset the “Ready to charge"” level and 2) the "Delay before recharging" time has passed since the opening of the allow charging contactor.
424 -)))
425 -
426 426  === Discharge ===
427 427  
428 428  The device controls the discharging contactor to connect battery to the load.
... ... @@ -490,7 +490,7 @@
490 490  * Switch off the discharging contactor on errors without delay – a flag to protectively open the discharging contactor without a delay. In the opposite case, when an error is detected, the discharging contactor opens always with the delay “Delay before stopping discharging”.
491 491  * Precharge time – a duration of closing the precharge contactor before closing the discharging contactor, millisecond;
492 492  * Voltage to clear the “Ready to discharge” – a threshold voltage level on the cell, V; if the voltage of any cell is below this level, the “Ready to discharge” signal is cleared;
493 -* Voltage to reset the “Ready to discharge” – a tolerant voltage level on the cell, V; if all cells voltages are above the tolerant level, the “Ready to discharge” signal is set;
485 +* Voltage to reset the “Ready to discharge” – a tolerant voltage level on the cell, V; if all cells voltages are above the tolerant level, the “Ready to discharge” signal is set.
494 494  
495 495  === Charge/Discharge ===
496 496  
1740399783613-216.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +59.8 KB
Content