Changes for page 3.3 Control

Last modified by Admin on 2025/04/09 12:15

From 23.3 to 24.1 From 24.2 to 24.3

From version 24.1

edited by Admin
on 2025/02/24 12:16

Change comment: Загрузить новое вложение 1740399363134-722.png

To version 24.2

edited by Admin
on 2025/02/24 12:17

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -364,51 +364,40 @@
  The device supports three charge control algorithms:
--* charging is always allowed;
--* charging is allowed when there is a signal “Charger connected”;
--* charging is allowed when there is a signal “Charge request”.
++* Always on – charging is always allowed;
++* On charger connected – charging is allowed when there is a signal “Charger connected”;
++* On charge request – charging is allowed when there is a signal “Charge request”.
--If the "**Always on**" algorithm is selected, the charging contactor and the allow charging contactor are always closed. If at least one of the errors appears:
++If the "**Always on**" algorithm is selected, the charging contactor and the allow charging contactor are always closed. If at least one of the errors from the "Errors 1, 2 ..." bitfields appears or one of the signals:
--* Overvoltage;
--* Overcurrent;
--* High temperature (CH);
--* Low temperature (CH);
--* HYG offline (optional);
--* Combilift offline (optional);
--* Spirit offline (optional);
--* Spirit charger error (optional);
--* Short circuit (optional);
--* High contactor temperature (optional);
--* CH contactor cycles error;
--* Critical error
++* Service reset;
++* Power down request;
++* Inhibit charging,
  both contactors are open (no current flows).
--When the algorithm "**On Charger connected**" is selected, the control is performed as follows:
++When the algorithm "**On charger connected**" is selected, the control is performed as follows:
--* If there is a signal “Charger connected” and there are no errors (see the list above), then through the delay time T,,on,, the charging contactor and the allow charging contactor close;
++* If there is a signal “Charger connected” and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the charging contactor and the allow charging contactor close;
  * If the signal “Charger connected” disappears, the allow charging contactor opens and after the delay time T,,off,, the charging contactor opens;
  * If in the process of charging the voltage on the cell exceeds the “Ready to charge” level, the allow charging contactor opens (while the charging contactor remains closed);
--* If errors in the list above occur the charging contactor and allow charging contactor open.
++* If errors from the "Errors 1, 2 ..." bitfields occur the charging contactor and allow charging contactor open.
--When the "**On Charge request**" algorithm selected, the control is performed as follows:
++When the "**On charge request**" algorithm selected, the control is performed as follows:
--* If there is a signal “Charge request” and there are no errors (see the list above), then through the delay time T,,on,, the charging contactor and the allow charging contactor close;
++* If there is a signal “Charge request” and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the charging contactor and the allow charging contactor close;
  * If the signal “Charge request” disappears, the allow charging contactor opens and after the delay time T,,off,, the charging contactor opens;
  * If in the process of charging the voltage on the cell exceeds the “Ready to charge” level, the allow charging contactor opens (while the charging contactor remains closed);
--* If errors in the list above occur the charging contactor and allow charging contactor open.
++* If errors from the "Errors 1, 2 ..." bitfields occur the charging contactor and allow charging contactor open.
  (% class="box infomessage" %)
  (((
--Note: when errors occur in the system, the **charging **contactor opens either immediately or with the delay T,,off,, (depends on the settings described below).
++**Note: **when errors occur in the system, the **Charge **contactor opens either immediately or with the delay T,,off,, (depends on the settings described below).
  )))
--When the power down request occurs, the allow charging contactor opens immediately and the charging contactor opens after the delay T,,off,,. Reclosing the charging contactor and allow charging contactor is performed if the power down request is removed.
--
  To change the parameters of the battery charge control algorithm, select the "Control → Charge" section:
--[[image:1733746766516-845.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="319" width="800"]]
++[[image:1740399363134-722.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="306" width="800"]]
  In this section:

Changes for page 3.3 Control

Summary

Details

Applications

Navigation

Table of Contents