Wiki source code of 2. Installation and connection

Version 5.1 by Admin on 2024/12/16 13:31

version	line-number	content
1.1	1	(% data-numbered-headings-start="2" style="--numbered-headings-start: 1;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
	2	= Installation and connection =
	3
	4	== Installation ==
	5
2.1	6	The mounting area of the BMS Main X must be protected from mechanical particles (dust, dirt, large objects) and water.
1.1	7
	8	The installation site must provide convenient access for subsequent connection to the device’s headers for connecting other system elements: contactors, temperature sensors, etc.
	9
2.1	10	Overall and mounting dimensions of the BMS Main X are shown below.
1.1	11
	12	[[image:1734355103230-973.png\|\|data-xwiki-image-style-alignment="center" height="460" width="450"]]
	13	[[image:1734355103237-284.png\|\|data-xwiki-image-style-alignment="center" height="207" width="450"]]
	14
	15	\|(((
	16	Parameter
	17	)))\|Value
	18	\|(((
	19	Overall dimensions (length × width × height), mm
	20	)))\|105 × 115 × 15
	21	\|Mounting dimensions (length × width), mm\|99 × 109
	22	\|Mounting holes\|M3
	23
	24	== Connection ==
	25
	26	=== Headers ===
	27
	28	There are names and locations of the BMS Main X headers in figure below.
	29
	30	[[image:1734355208744-833.png\|\|data-xwiki-image-style-alignment="center" height="491" width="450"]]
	31
	32	=== Х1 – header for power supply ===
	33
	34	[[image:1734355208747-667.png\|\|data-xwiki-image-style-alignment="center"]]
	35
	36	\|Pin\|Name\|Description
	37	\|1\|V+\|Supply voltage 18÷36V
	38	\|2\|GND\|Ground
	39
	40	=== X2 – header for USB ===
	41
	42	=== X3 – header for CAN (INT) interface ===
	43
	44	[[image:1734355229969-197.png\|\|data-xwiki-image-style-alignment="center"]]
	45
	46	\|Pin\|Name\|Description
	47	\|1\|СAN_INT_H\|CAN-H line of the internal CAN bus (communication with battery modules)
	48	\|2\|CAN_INT_L\|CAN-L line of the internal CAN bus (communication with battery modules)
	49	\|3\|CAN_INT_5V\|Isolated 5V power supply for internal devices, max 200 mA
	50	\|4\|CAN_INT_GND\|Isolated ground
	51
	52	=== Х4 – header for RS-485 interface ===
	53
	54	[[image:1734355229969-197.png\|\|data-xwiki-image-style-alignment="center"]]
	55
	56	\|Pin\|Name\|Description
	57	\|1\|RS485_A\|A line of the external RS-485 bus
	58	\|2\|RS485_B\|B line of the external RS-485 bus
	59	\|3\|-\|-
	60	\|4\|RS485_GND\|Isolated ground
	61
	62	=== J1 – jumper for switching RS-485 terminal resistor ===
	63
	64	To connect the terminal resistor between the RS485_A and RS485_B lines, install the jumper J1 according to the following figure:
	65
	66	[[image:1734355346488-798.png\|\|data-xwiki-image-style-alignment="center"]]
2.1	67
	68	=== Х5 – header for CAN (EXT) interface ===
	69
3.1	70	[[image:1734355229969-197.png\|\|data-xwiki-image-style-alignment="center"]]
2.1	71
	72	\|Pin\|Name\|Description
	73	\|1\|СAN_EXT_H\|CAN-H line of the external CAN bus (communication with a top-level system)
	74	\|2\|CAN_EXT_L\|CAN-L line of the external CAN bus (communication with a top-level system)
	75	\|3\|CAN_EXT_5V\|Isolated 5V power supply for external devices, max 200 mA
	76	\|4\|CAN_EXT_GND\|Isolated ground
	77
3.1	78	=== J2 – jumper for switching CAN (EXT) terminal resistor ===
	79
	80	To connect the terminal resistor between the CAN_EXT_H and CAN_EXT_L lines, install the jumper J2 according to the following figure:
	81
	82	[[image:1734355346488-798.png\|\|data-xwiki-image-style-alignment="center"]]
	83
	84	=== Х6 – header for sold-state relays ===
	85
	86	[[image:1734355584041-898.jpeg\|\|data-xwiki-image-style-alignment="center" height="65" width="90"]]
	87
	88	\|Pin\|Name\|Description
	89	\|1\|NO1\|Normally open contact of the relay 1
	90	\|2\|NO2\|Normally open contact of the relay 2
	91	\|3\|NO3\|Normally open contact of the relay 3
	92	\|4\|COM1\|Common contact of the relay 1 (55V, 2A)
	93	\|5\|COM2\|Common contact of the relay 2 (55V, 2A)
	94	\|6\|COM3\|Common contact of the relay 3 (55V, 2A)
	95
	96	=== X7 – header for discrete inputs/outputs ===
	97
5.1	98	[[image:1734355584043-416.jpeg\|\|data-xwiki-image-style-alignment="center" height="79" width="260"]]
3.1	99
	100	\|Pin\|Name\|Description
	101	\|1\|GND\|Discrete input 1 “dry contact” (ground)
	102	\|2\|GND\|Discrete input 2 “dry contact” (ground)
	103	\|3\|GND\|Discrete input 3 “dry contact” (ground)
	104	\|4\|GND\|Discrete input 4 “dry contact” (ground)
	105	\|5\|-\|-
	106	\|6\|GND\|Discrete output 1 (ground)
	107	\|7\|GND\|Discrete output 2 (ground)
	108	\|8\|GND\|Discrete output 3 (ground)
	109	\|9\|GND\|Discrete output 4 (ground)
	110	\|10\|D_IN1\|Discrete input 1 “dry contact” (+5V)
	111	\|11\|D_IN2\|Discrete input 2 “dry contact” (+5V)
	112	\|12\|D_IN3\|Discrete input 3 “dry contact” (+5V)
	113	\|13\|D_IN4\|Discrete input 4 “dry contact” (+5V)
	114	\|14\|-\|-
	115	\|15\|D_OUT1\|Discrete output 1 (+5V, 20mA)
	116	\|16\|D_OUT2\|Discrete output 2 (+5V, 20mA)
	117	\|17\|D_OUT3\|Discrete output 3 (+5V, 20mA)
	118	\|18\|D_OUT4\|Discrete output 4 (+5V, 20mA)
	119
	120	=== Х8 – header for temperature sensors ===
	121
	122	[[image:1734355229969-197.png\|\|data-xwiki-image-style-alignment="center"]]
	123
	124	\|Pin\|Name\|Description
	125	\|1\|TEMPG1\|Ground of the thermistor 1
	126	\|2\|TEMPG2\|Ground of the thermistor 2
	127	\|3\|TEMP1\|Signal from the thermistor 1
	128	\|4\|TEMP2\|Signal from the thermistor 2
	129
2.1	130

Wiki source code of 2. Installation and connection

Applications

Navigation

Table of Contents