Skip to Content

Wiki source code of 2. Installation and connection

Version 5.1 by Admin on 2024/12/16 13:31

Show last authors

author	version	line-number	content
		1	(% data-numbered-headings-start="2" style="--numbered-headings-start: 1;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
		2	= Installation and connection =
		3
		4	== Installation ==
		5
		6	The mounting area of the BMS Main X must be protected from mechanical particles (dust, dirt, large objects) and water.
		7
		8	The installation site must provide convenient access for subsequent connection to the device’s headers for connecting other system elements: contactors, temperature sensors, etc.
		9
		10	Overall and mounting dimensions of the BMS Main X are shown below.
		11
		12	[[image:1734355103230-973.png\|\|data-xwiki-image-style-alignment="center" height="460" width="450"]]
		13	[[image:1734355103237-284.png\|\|data-xwiki-image-style-alignment="center" height="207" width="450"]]
		14
		15	\|(((
		16	Parameter
		17	)))\|Value
		18	\|(((
		19	Overall dimensions (length × width × height), mm
		20	)))\|105 × 115 × 15
		21	\|Mounting dimensions (length × width), mm\|99 × 109
		22	\|Mounting holes\|M3
		23
		24	== Connection ==
		25
		26	=== Headers ===
		27
		28	There are names and locations of the BMS Main X headers in figure below.
		29
		30	[[image:1734355208744-833.png\|\|data-xwiki-image-style-alignment="center" height="491" width="450"]]
		31
		32	=== Х1 – header for power supply ===
		33
		34	[[image:1734355208747-667.png\|\|data-xwiki-image-style-alignment="center"]]
		35
		36	\|Pin\|Name\|Description
		37	\|1\|V+\|Supply voltage 18÷36V
		38	\|2\|GND\|Ground
		39
		40	=== X2 – header for USB ===
		41
		42	=== X3 – header for CAN (INT) interface ===
		43
		44	[[image:1734355229969-197.png\|\|data-xwiki-image-style-alignment="center"]]
		45
		46	\|Pin\|Name\|Description
		47	\|1\|СAN_INT_H\|CAN-H line of the internal CAN bus (communication with battery modules)
		48	\|2\|CAN_INT_L\|CAN-L line of the internal CAN bus (communication with battery modules)
		49	\|3\|CAN_INT_5V\|Isolated 5V power supply for internal devices, max 200 mA
		50	\|4\|CAN_INT_GND\|Isolated ground
		51
		52	=== Х4 – header for RS-485 interface ===
		53
		54	[[image:1734355229969-197.png\|\|data-xwiki-image-style-alignment="center"]]
		55
		56	\|Pin\|Name\|Description
		57	\|1\|RS485_A\|A line of the external RS-485 bus
		58	\|2\|RS485_B\|B line of the external RS-485 bus
		59	\|3\|-\|-
		60	\|4\|RS485_GND\|Isolated ground
		61
		62	=== J1 – jumper for switching RS-485 terminal resistor ===
		63
		64	To connect the terminal resistor between the RS485_A and RS485_B lines, install the jumper J1 according to the following figure:
		65
		66	[[image:1734355346488-798.png\|\|data-xwiki-image-style-alignment="center"]]
		67
		68	=== Х5 – header for CAN (EXT) interface ===
		69
		70	[[image:1734355229969-197.png\|\|data-xwiki-image-style-alignment="center"]]
		71
		72	\|Pin\|Name\|Description
		73	\|1\|СAN_EXT_H\|CAN-H line of the external CAN bus (communication with a top-level system)
		74	\|2\|CAN_EXT_L\|CAN-L line of the external CAN bus (communication with a top-level system)
		75	\|3\|CAN_EXT_5V\|Isolated 5V power supply for external devices, max 200 mA
		76	\|4\|CAN_EXT_GND\|Isolated ground
		77
		78	=== J2 – jumper for switching CAN (EXT) terminal resistor ===
		79
		80	To connect the terminal resistor between the CAN_EXT_H and CAN_EXT_L lines, install the jumper J2 according to the following figure:
		81
		82	[[image:1734355346488-798.png\|\|data-xwiki-image-style-alignment="center"]]
		83
		84	=== Х6 – header for sold-state relays ===
		85
		86	[[image:1734355584041-898.jpeg\|\|data-xwiki-image-style-alignment="center" height="65" width="90"]]
		87
		88	\|Pin\|Name\|Description
		89	\|1\|NO1\|Normally open contact of the relay 1
		90	\|2\|NO2\|Normally open contact of the relay 2
		91	\|3\|NO3\|Normally open contact of the relay 3
		92	\|4\|COM1\|Common contact of the relay 1 (55V, 2A)
		93	\|5\|COM2\|Common contact of the relay 2 (55V, 2A)
		94	\|6\|COM3\|Common contact of the relay 3 (55V, 2A)
		95
		96	=== X7 – header for discrete inputs/outputs ===
		97
		98	[[image:1734355584043-416.jpeg\|\|data-xwiki-image-style-alignment="center" height="79" width="260"]]
		99
		100	\|Pin\|Name\|Description
		101	\|1\|GND\|Discrete input 1 “dry contact” (ground)
		102	\|2\|GND\|Discrete input 2 “dry contact” (ground)
		103	\|3\|GND\|Discrete input 3 “dry contact” (ground)
		104	\|4\|GND\|Discrete input 4 “dry contact” (ground)
		105	\|5\|-\|-
		106	\|6\|GND\|Discrete output 1 (ground)
		107	\|7\|GND\|Discrete output 2 (ground)
		108	\|8\|GND\|Discrete output 3 (ground)
		109	\|9\|GND\|Discrete output 4 (ground)
		110	\|10\|D_IN1\|Discrete input 1 “dry contact” (+5V)
		111	\|11\|D_IN2\|Discrete input 2 “dry contact” (+5V)
		112	\|12\|D_IN3\|Discrete input 3 “dry contact” (+5V)
		113	\|13\|D_IN4\|Discrete input 4 “dry contact” (+5V)
		114	\|14\|-\|-
		115	\|15\|D_OUT1\|Discrete output 1 (+5V, 20mA)
		116	\|16\|D_OUT2\|Discrete output 2 (+5V, 20mA)
		117	\|17\|D_OUT3\|Discrete output 3 (+5V, 20mA)
		118	\|18\|D_OUT4\|Discrete output 4 (+5V, 20mA)
		119
		120	=== Х8 – header for temperature sensors ===
		121
		122	[[image:1734355229969-197.png\|\|data-xwiki-image-style-alignment="center"]]
		123
		124	\|Pin\|Name\|Description
		125	\|1\|TEMPG1\|Ground of the thermistor 1
		126	\|2\|TEMPG2\|Ground of the thermistor 2
		127	\|3\|TEMP1\|Signal from the thermistor 1
		128	\|4\|TEMP2\|Signal from the thermistor 2
		129
		130