Skip to Content
Last modified by Admin on 2025/03/18 12:50
From version 1.1
edited by Admin
on 2024/12/16 13:23
Change comment: There is no comment for this version
To version 7.1
edited by Admin
on 2025/02/20 13:13
Change comment: There is no comment for this version

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -drafts.BMS Main X.WebHome
1 +Battery management systems.BMS Main X.WebHome
Content
... ... @@ -3,11 +3,11 @@
3 3  
4 4  == Installation ==
5 5  
6 -The mounting area of the BMS Main X 2.x must be protected from mechanical particles (dust, dirt, large objects) and water.
6 +The mounting area of the BMS Main X must be protected from mechanical particles (dust, dirt, large objects) and water.
7 7  
8 8  The installation site must provide convenient access for subsequent connection to the device’s headers for connecting other system elements: contactors, temperature sensors, etc.
9 9  
10 -Overall and mounting dimensions of the BMS Main X 2.x are shown in Figures 6 and 7.
10 +Overall and mounting dimensions of the BMS Main X are shown below.
11 11  
12 12  [[image:1734355103230-973.png||data-xwiki-image-style-alignment="center" height="460" width="450"]]
13 13  [[image:1734355103237-284.png||data-xwiki-image-style-alignment="center" height="207" width="450"]]
... ... @@ -20,6 +20,7 @@
20 20  )))|105 × 115 × 15
21 21  |Mounting dimensions (length × width), mm|99 × 109
22 22  |Mounting holes|M3
23 +|Headers X1, X3-X8 type|Molex series Micro-Fit
23 23  
24 24  == Connection ==
25 25  
... ... @@ -31,6 +31,8 @@
31 31  
32 32  === Х1 – header for power supply ===
33 33  
35 +Receptacle Housing: Molex 436450200. Terminals: Molex 43030
36 +
34 34  [[image:1734355208747-667.png||data-xwiki-image-style-alignment="center"]]
35 35  
36 36  |**Pin**|**Name**|**Description**
... ... @@ -41,6 +41,8 @@
41 41  
42 42  === X3 – header for CAN (INT) interface ===
43 43  
47 +Receptacle Housing: Molex 430250400. Terminals: Molex 43030
48 +
44 44  [[image:1734355229969-197.png||data-xwiki-image-style-alignment="center"]]
45 45  
46 46  |**Pin**|**Name**|**Description**
... ... @@ -51,6 +51,8 @@
51 51  
52 52  === Х4 – header for RS-485 interface ===
53 53  
59 +Receptacle Housing: Molex 430250400. Terminals: Molex 43030
60 +
54 54  [[image:1734355229969-197.png||data-xwiki-image-style-alignment="center"]]
55 55  
56 56  |**Pin**|**Name**|**Description**
... ... @@ -64,3 +64,75 @@
64 64  To connect the terminal resistor between the** RS485_A** and **RS485_B** lines, install the jumper J1 according to the following figure:
65 65  
66 66  [[image:1734355346488-798.png||data-xwiki-image-style-alignment="center"]]
74 +
75 +=== Х5 – header for CAN (EXT) interface ===
76 +
77 +Receptacle Housing: Molex 430250400. Terminals: Molex 43030
78 +
79 +[[image:1734355229969-197.png||data-xwiki-image-style-alignment="center"]]
80 +
81 +|**Pin**|**Name**|**Description**
82 +|**1**|**СAN_EXT_H**|CAN-H line of the external CAN bus (communication with a top-level system)
83 +|**2**|**CAN_EXT_L**|CAN-L line of the external CAN bus (communication with a top-level system)
84 +|**3**|**CAN_EXT_5V**|Isolated 5V power supply for external devices, max 200 mA
85 +|**4**|**CAN_EXT_GND**|Isolated ground
86 +
87 +=== J2 – jumper for switching CAN (EXT) terminal resistor ===
88 +
89 +To connect the terminal resistor between the** CAN_EXT_H** and **CAN_EXT_L** lines, install the jumper J2 according to the following figure:
90 +
91 +[[image:1734355346488-798.png||data-xwiki-image-style-alignment="center"]]
92 +
93 +=== Х6 – header for sold-state relays ===
94 +
95 +Receptacle Housing: Molex 430250600. Terminals: Molex 43030
96 +
97 +[[image:1734355584041-898.jpeg||data-xwiki-image-style-alignment="center" height="65" width="90"]]
98 +
99 +|**Pin**|**Name**|**Description**
100 +|**1**|**NO1**|Normally open contact of the relay 1
101 +|**2**|**NO2**|Normally open contact of the relay 2
102 +|**3**|**NO3**|Normally open contact of the relay 3
103 +|**4**|**COM1**|Common contact of the relay 1 (55V, 2A)
104 +|**5**|**COM2**|Common contact of the relay 2 (55V, 2A)
105 +|**6**|**COM3**|Common contact of the relay 3 (55V, 2A)
106 +
107 +=== X7 – header for discrete inputs/outputs ===
108 +
109 +Receptacle Housing: Molex 430251800. Terminals: Molex 43030
110 +
111 +[[image:1734355584043-416.jpeg||data-xwiki-image-style-alignment="center" height="79" width="260"]]
112 +
113 +|**Pin**|**Name**|**Description**
114 +|**1**|**GND**|Discrete input 1 “dry contact” (ground)
115 +|**2**|**GND**|Discrete input 2 “dry contact” (ground)
116 +|**3**|**GND**|Discrete input 3 “dry contact” (ground)
117 +|**4**|**GND**|Discrete input 4 “dry contact” (ground)
118 +|**5**|**-**|-
119 +|**6**|**GND**|Discrete output 1 (ground)
120 +|**7**|**GND**|Discrete output 2 (ground)
121 +|**8**|**GND**|Discrete output 3 (ground)
122 +|**9**|**GND**|Discrete output 4 (ground)
123 +|**10**|**D_IN1**|Discrete input 1 “dry contact” (+5V)
124 +|**11**|**D_IN2**|Discrete input 2 “dry contact” (+5V)
125 +|**12**|**D_IN3**|Discrete input 3 “dry contact” (+5V)
126 +|**13**|**D_IN4**|Discrete input 4 “dry contact” (+5V)
127 +|**14**|**-**|-
128 +|**15**|**D_OUT1**|Discrete output 1 (+5V, 20mA)
129 +|**16**|**D_OUT2**|Discrete output 2 (+5V, 20mA)
130 +|**17**|**D_OUT3**|Discrete output 3 (+5V, 20mA)
131 +|**18**|**D_OUT4**|Discrete output 4 (+5V, 20mA)
132 +
133 +=== Х8 – header for temperature sensors ===
134 +
135 +Receptacle Housing: Molex 430250400. Terminals: Molex 43030
136 +
137 +[[image:1734355229969-197.png||data-xwiki-image-style-alignment="center"]]
138 +
139 +|**Pin**|**Name**|**Description**
140 +|**1**|**TEMPG1**|Ground of the thermistor 1
141 +|**2**|**TEMPG2**|Ground of the thermistor 2
142 +|**3**|**TEMP1**|Signal from the thermistor 1
143 +|**4**|**TEMP2**|Signal from the thermistor 2
144 +
145 +
1734355584041-898.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +12.0 KB
Content
1734355584043-416.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +24.8 KB
Content