Skip to Content

Changes for page 3.5 External equipment

Last modified by Admin on 2025/05/30 16:50
From version 7.4
edited by Admin
on 2025/02/11 17:25
Change comment: There is no comment for this version
To version 4.1
edited by Admin
on 2025/02/11 17:20
Change comment: Uploaded new attachment "1739294413209-387.png", version {1}

Summary

Details

Page properties
Content
... ... @@ -30,12 +30,11 @@
30 30  
31 31  Communication parameters via the Basic J1939 protocol are configured in the “External equipment – Basic J1939 vehicle” section:
32 32  
33 -[[image:1739294413209-387.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="76" width="600"]]
34 34  
35 35  In this section:
36 36  
37 37  * Enable – a flag to enable communication using the protocol;
38 -* CAN port – port which is used to communicate with the vehicle:
37 +* CAN port – port which is used to communicate with the charger:
39 39  ** CAN1 (ext);
40 40  ** CAN2 (int);
41 41  * BMS message ID – an identifier of the first message of the device in the J1939 network;
... ... @@ -45,69 +45,10 @@
45 45  
46 46  Communication parameters for the Evocargo vehicle are configured in the section "External equipment – Evocargo vehicle":
47 47  
48 -[[image:1739294432727-315.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="83" width="600"]]
47 +[[image:1734357302172-818.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="89" width="600"]]
49 49  
50 50  In this section:
51 51  
52 52  * Enable – a flag to enable communication with the Evocargo vehicle;
53 -* CAN port – port which is used to communicate with the vehicle:
54 -** CAN1 (ext);
55 -** CAN2 (int);
56 56  * Minimum voltage – minimum battery voltage, V;
57 57  * Maximum voltage – maximum battery voltage, V.
58 -
59 -=== BMS IMD ===
60 -
61 -To change communication parameters with an insulation monitoring device BMS IMD, select the "External equipment → BMD IMD " section:
62 -
63 -[[image:1739294477662-343.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="100" width="600"]]
64 -
65 -In this section:
66 -
67 -* Enable – a flag to enable communication with the IMD;
68 -* CAN port – port which is used to communicate with the IMD:
69 -** CAN1 (ext);
70 -** CAN2 (int);
71 -* Node ID – a CANopen address of the BMS IMD device;
72 -* Configure IMD – a flag to override the IMD warning and alarm settings;
73 -* Allow work if battery modules are joined – a flag to allow the BMS IMD to work only if battery modules are joined;
74 -* Alarm threshold – a threshold resistance value to set insulation alarm, Ohm;
75 -* Warning threshold – a threshold resistance value to set insulation warning, Ohm.
76 -
77 -=== Unibat vehicle ===
78 -
79 -To change communication parameters with vehicle with Unibat battery installed, select the "External equipment → Unibat vehicle" section:
80 -
81 -[[image:1739294567774-840.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="290" width="600"]]
82 -
83 -In this section:
84 -
85 -* Enable – a flag to enable communication with the vehicle;
86 -* CAN port – port which is used to communicate with the vehicle;
87 -* Use CRC – a flag to enable checking the checksum of the control message;
88 -* Use DTC – a flag to enable transmit of error codes on battery failures;
89 -* Use additional current sensors to determine error – a flag to use measuring of second and third current sensor to determine errors in battery work;
90 -* Number of modules – total number of battery modules;
91 -* Receive timeout – a timeout for receiving packets from the vehicle (if there is no messages during that time, an error generates), millisecond;
92 -* HVIL delay – a delay before generating a signal of high-voltage interrupt loop breakage, millisecond;
93 -* Nominal voltage, V;
94 -* Maximum charge voltage, V;
95 -* Lower voltage limit, V;
96 -* Upper voltage limit, V;
97 -* Lower temperature limit, °C;
98 -* Upper temperature limit, °C;
99 -* Lower SOC limit, %;
100 -* Upper SOC limit, %;
101 -* Lower cell voltage limit, V;
102 -* Upper cell voltage limit, V;
103 -* Nominal capacity – nominal battery capacity, Wh;
104 -* Current threshold for contactor opening – a current value for safe contactor opening, A;
105 -* Waiting time until the current drops below the threshold – a waiting time for current to drop below estimated value before safe contactor opening, millisecond;
106 -* Control ventilation fans – a flag to send command messages to control battery ventilation fans;
107 -* Version: Manufacturer;
108 -* Version: Hardware ID;
109 -* Version: Software ID;
110 -* Version: Confoguration;
111 -* Version: Serial Number;
112 -* Version: Production date;
113 -* Errors 1, 2 for emergency shutdown – a bitfield with errors to emergency shutdown the
1739294432727-315.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -17.1 KB
Content
1739294477662-343.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -22.4 KB
Content
1739294567774-840.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -84.0 KB
Content