Skip to Content

Changes for page 3.5 External equipment

Last modified by Admin on 2025/05/30 16:50
From version 7.2
edited by Admin
on 2025/02/11 17:22
Change comment: There is no comment for this version
To version 16.1
edited by Admin
on 2025/05/30 16:50
Change comment: Загрузить новое вложение 1748623852682-730.png

Summary

Details

Page properties
Content
... ... @@ -60,10 +60,8 @@
60 60  
61 61  To change communication parameters with an insulation monitoring device BMS IMD, select the "External equipment → BMD IMD " section:
62 62  
63 -[[image:1739294477662-343.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="100" width="600"]]
63 +[[image:1739294477662-343.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="100" width="600"]]In this section:
64 64  
65 -In this section:
66 -
67 67  * Enable – a flag to enable communication with the IMD;
68 68  * CAN port – port which is used to communicate with the IMD:
69 69  ** CAN1 (ext);
... ... @@ -74,8 +74,72 @@
74 74  * Alarm threshold – a threshold resistance value to set insulation alarm, Ohm;
75 75  * Warning threshold – a threshold resistance value to set insulation warning, Ohm.
76 76  
77 -=== Unibat vehicle ===
75 +=== Unibat vehicle ===
78 78  
79 79  To change communication parameters with vehicle with Unibat battery installed, select the "External equipment → Unibat vehicle" section:
80 80  
81 -[[image:1739294567774-840.png]]
79 +[[image:1748623056947-344.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="347" width="600"]]
80 +
81 +In this section:
82 +
83 +* Enable – a flag to enable communication with the vehicle;
84 +* CAN port – port which is used to communicate with the vehicle;
85 +* BMS address;
86 +* VCU address;
87 +* Use CRC – a flag to enable checking the checksum of the control message;
88 +* Use DTC – a flag to enable transmit of error codes on battery failures;
89 +* Use additional current sensors to determine error – a flag to use measuring of second and third current sensor to determine errors in battery work;
90 +* Use continuous charge current limit – a flag to use continuous charge current limit;
91 +* Invert discharge current limit;
92 +* Disable insulation measurement;
93 +* Number of modules – total number of battery modules;
94 +* Receive timeout – a timeout for receiving packets from the vehicle (if there is no messages during that time, an error generates), millisecond;
95 +* HVIL delay – a delay before generating a signal of high-voltage interrupt loop breakage, millisecond;
96 +* Nominal voltage, V;
97 +* Maximum charge voltage, V;
98 +* Lower voltage limit, V;
99 +* Upper voltage limit, V;
100 +* Lower temperature limit, °C;
101 +* Upper temperature limit, °C;
102 +* Lower SOC limit, %;
103 +* Upper SOC limit, %;
104 +* Lower cell voltage limit, V;
105 +* Upper cell voltage limit, V;
106 +* Nominal capacity – nominal battery capacity, Wh;
107 +* Current threshold for contactor opening – a current value for safe contactor opening, A;
108 +* Waiting time until the current drops below the threshold – a waiting time for current to drop below estimated value before safe contactor opening, millisecond;
109 +* Bus voltage threshold for contactor opening – a voltage value for safe contactor opening, V;
110 +* Waiting time until the voltage drops below the threshold – a waiting time for voltage to drop below estimated value before safe contactor opening, millisecond;
111 +* Insulation measurement period;
112 +* Waiting time for assembling minimum number of modules;
113 +* Control ventilation fans – a flag to send command messages to control battery ventilation fans;
114 +* Version: Manufacturer;
115 +* Version: Hardware ID;
116 +* Version: Software ID;
117 +* Version: Configuration;
118 +* Version: Serial Number;
119 +* Version: Production date;
120 +* Errors 1, 2 for emergency shutdown – a bitfield with errors to emergency shutdown the vehicle.
121 +
122 +=== ATIB charger ===
123 +
124 +To change the parameters of communication with an ATIB Elettronica charger, select the "External equipment → ATIB charger" section:
125 +[[image:1739294769684-405.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="90" width="600"]]
126 +
127 +In this section:
128 +
129 +* Enable – a flag to enable communication with the charger;
130 +* CAN port – port which is used to communicate with the charger:
131 +** CAN1 (ext);
132 +** CAN2 (int);
133 +* Receive timeout – a timeout for receiving packets from the charger (if there is no data being received from the charger for a given time, the connection loss flag is set), millisecond;
134 +* Output period - a period of sending commands to the charger, millisecond;
135 +* Charging voltage – maximum charging voltage, V;
136 +* Set “Charger connected” signal if the charger is online – a flag to generate the “Charger connected” signal if connection with the charger is established.
137 +
138 +(% class="box infomessage" %)
139 +(((
140 +After changing the settings, restart the BMS Main 3X device.
141 +)))
142 +
143 +
1739294769684-405.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +21.5 KB
Content
1739970298499-463.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +85.1 KB
Content
1748623056947-344.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +91.2 KB
Content
1748623852682-730.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +91.2 KB
Content