Skip to Content

Changes for page 3.4 Protections

Last modified by Admin on 2025/04/09 12:19
From version 6.1
edited by Admin
on 2024/12/24 18:36
Change comment: There is no comment for this version
To version 9.2
edited by Admin
on 2024/12/26 14:47
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -42,6 +42,14 @@
42 42  If there is the "Overcurrent" error, the **charging **and **discharging **contactors open.
43 43  )))
44 44  
45 +=== Charge current limit ===
46 +
47 +TBA
48 +
49 +=== Discharge current limit ===
50 +
51 +TBA
52 +
45 45  === Undervoltage ===
46 46  
47 47  The BMS Main 3 device implements battery protection from too low voltage on the cells.
... ... @@ -48,7 +48,7 @@
48 48  
49 49  To change the battery protection parameters from low voltage on the cells, select the "Protections → Undervoltage" section:
50 50  
51 -[[image:1733328382380-760.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="127" width="800"]]
59 +[[image:1735224224155-829.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="112" width="800"]]
52 52  
53 53  In this section:
54 54  
... ... @@ -55,6 +55,7 @@
55 55  * Enable – a flag to enable the protection;
56 56  * Minimum cell voltage, V;
57 57  * Tolerant cell voltage, V;
66 +* Check the open circuit voltage instead of the actual voltage – a flag to enable the check of voltage correction due to current and cell resistance;
58 58  * Delay before setting the error, millisecond;
59 59  * Delay before clearing the error, second;
60 60  * Lock – a flag to block the error until the device is restarted.
... ... @@ -80,7 +80,7 @@
80 80  
81 81  To change the battery protection parameters from high voltage on the cells, select the "Protections → Overvoltage" section:
82 82  
83 -[[image:1733328382382-607.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="138" width="800"]]
92 +[[image:1735224377252-473.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="114" width="800"]]
84 84  
85 85  In this section:
86 86  
... ... @@ -87,9 +87,9 @@
87 87  * Enable – a flag to enable the protection;
88 88  * Maximum cell voltage, V;
89 89  * Tolerant cell voltage, V;
99 +* Check the open circuit voltage instead of the actual voltage – a flag to enable the check of voltage correction due to current and cell resistance;
90 90  * Delay before setting the error, millisecond;
91 91  * Delay before clearing the error, second;
92 -* Switch off the discharging contactor on error – a flag to open the discharging contactor when the "Overvoltage" error is generated;
93 93  * Lock – a flag to block the error until the device is restarted.
94 94  
95 95  As a result of the operation of the battery protection from high voltage, the "Overvoltage" error is generated.
... ... @@ -269,7 +269,7 @@
269 269  If there is the “Water” error, the **“Critical error”** is generated and **all relays open**.
270 270  )))
271 271  
272 -=== High Logic temperature ===
281 +=== Logic high temperature ===
273 273  
274 274  To change the overheating protection parameters of BMS Logic devices, select the "Protections → High Logic temperature" section:
275 275  
... ... @@ -503,6 +503,10 @@
503 503  If there is the "Power switch error", the **“Critical error” **is generated and **all relays open.**
504 504  )))
505 505  
515 +=== Power fault ===
516 +
517 +TBA
518 +
506 506  === Charge contactor cycles ===
507 507  
508 508  The BMS Main 3 device protects the charging contactor against frequent switching.
1735224224155-829.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +23.4 KB
Content
1735224377252-473.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +23.4 KB
Content