Skip to Content

Changes for page 3.4 Protections

Last modified by Admin on 2026/04/01 08:42
From version 51.7
edited by Admin
on 2026/04/01 08:34
Change comment: There is no comment for this version
To version 51.6
edited by Admin
on 2026/04/01 08:33
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -409,10 +409,10 @@
409 409  In this section:
410 410  
411 411  * **Enable **– a flag to enable the protection;
412 -* **Number of cells** – a number of temperature sensors connected to the BMS;
413 -* **Delay before setting the error**, millisecond;
414 -* **Delay before clearing the error**, second;
415 -* **Lock **– a flag to block the error until the device is restarted.
412 +* Number of cells – a number of temperature sensors connected to the BMS;
413 +* Delay before setting the error, millisecond;
414 +* Delay before clearing the error, second;
415 +* Lock – a flag to block the error until the device is restarted.
416 416  
417 417  As a result of the operation of the protection from the mismatch of the number of cells, the "T-sensor count error" is generated.
418 418  
... ... @@ -437,12 +437,12 @@
437 437  
438 438  In this section:
439 439  
440 -* **Enable **– a flag to enable the protection;
441 -* **Logic count** – a number of BMS Logic devices connected to the BMS Main;
442 -* **Scan fast** – a flag to scan BMS Logic devices fast (devices with addresses from 1 to “Logic count” are scanned; this mode reduces BMS system startup time);
443 -* **Delay before setting the error** – a delay before setting the error //during initialization//, millisecond;
444 -* **Delay before clearing the error **– a delay before clearing the error //during initialization//, second;
445 -* **Lock** – lock the error until the device is reset.
440 +* Enable – a flag to enable the protection;
441 +* Logic count – a number of BMS Logic devices connected to the BMS Main;
442 +* Scan fast – a flag to scan BMS Logic devices fast (devices with addresses from 1 to “Logic count” are scanned; this mode reduces BMS system startup time);
443 +* Delay before setting the error – a delay before setting the error //during initialization//, millisecond;
444 +* Delay before clearing the error– a delay before clearing the error //during initialization//, second;
445 +* Lock – lock the error until the device is reset.
446 446  
447 447  As a result of the operation of the protection from the mismatch of the number of BMS Logic devices, the "Logic count error" is generated.
448 448  
... ... @@ -471,12 +471,12 @@
471 471  
472 472  In this section:
473 473  
474 -* **Level 1, 2, 3** – three protection levels. The following parameters are configured at each level:
475 -** **Enable **– a flag to enable the protection;
476 -** **Maximum current**, A;
477 -** **Delay before setting the error**, second;
478 -* **Delay before clearing the error**, second;
479 -* **Lock **– a flag to block the error until the device is restarted.
474 +* Level 1, 2, 3 – three protection levels. The following parameters are configured at each level:
475 +** Enable – a flag to enable the protection;
476 +** Maximum current, A;
477 +** Delay before setting the error, second;
478 +* Delay before clearing the error, second;
479 +* Lock – a flag to block the error until the device is restarted.
480 480  
481 481  If there is a short circuit, the "Short circuit" error is generated.
482 482  
... ... @@ -498,13 +498,13 @@
498 498  
499 499  In this section:
500 500  
501 -* **Enable** – a flag to enable the protection;
502 -* **Thermistor **– a selection of which cell thermistor will be used as contactor temperature sensor;
503 -* **Maximum contactor temperature**, °C;
504 -* **Tolerant contactor temperature**, °C;
505 -* **Delay before setting the error**, second;
506 -* **Delay before clearing the error**, second;
507 -* **Lock **– a flag to block the error until the device is restarted.
501 +* Enable – a flag to enable the protection;
502 +* Thermistor – a selection of which cell thermistor will be used as contactor temperature sensor;
503 +* Maximum contactor temperature, °C;
504 +* Tolerant contactor temperature, °C;
505 +* Delay before setting the error, second;
506 +* Delay before clearing the error, second;
507 +* Lock – a flag to block the error until the device is restarted.
508 508  
509 509  If there is a contactor overheat, the "High contactor temperature" error is generated.
510 510