Skip to Content

Changes for page 3.4 Protections

Last modified by Admin on 2025/04/09 12:19
From version 16.14
edited by Admin
on 2024/12/26 15:04
Change comment: There is no comment for this version
To version 13.3
edited by Admin
on 2024/12/26 14:55
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -44,17 +44,8 @@
44 44  
45 45  === Charge current limit ===
46 46  
47 -The BMS Main 3 device can check the charging current with the limit based on the Charge map. If current is more than estimated maximum, "Current limit" error is generated.
47 +TBA
48 48  
49 -To change the overcurrent protection of the battery, select the "Protections → Charge current limit" section:
50 -
51 -[[image:1735225207687-430.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="113" width="800"]]In this section:
52 -
53 -* Enable – a flag to enable the protection;
54 -* Threshold to switch from Region 1 to Region 2
55 -*
56 -
57 -
58 58  === Discharge current limit ===
59 59  
60 60  TBA
... ... @@ -753,7 +753,7 @@
753 753  * Source is ON: Upper current limit, A;
754 754  * Lock – a flag to block the error until the device is restarted.
755 755  
756 -If interlock loop breaks and its current is out of the configured ranges, the “HVIL error” is generated. Error clears if interlock loop is being restored.
747 +If interlock loop breaks and its current , the “HVIL error” is generated. Error clears if interlock loop is being restored.
757 757  
758 758  (% class="box warningmessage" %)
759 759  (((
... ... @@ -809,7 +809,7 @@
809 809  
810 810  To change the general error parameters, select the "Protections → Critical error" section:
811 811  
812 -[[image:1735224942262-497.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="102" width="800"]]
803 +[[image:1733328487101-216.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="262" width="800"]]
813 813  
814 814  In this section:
815 815  
... ... @@ -817,7 +817,7 @@
817 817  * Delay before setting the error, millisecond;
818 818  * Delay before clearing the error, second;
819 819  * Lock – a flag to block the error until the device is restarted;
820 -* Errors 1, 2 to set the "Critical error" – bitfields to enable check of corresponding errors.
811 +* Check: <error> – a flags to enable check of corresponding errors.
821 821  
822 822  The general error flag is generated if at least one of the enabled errors is generated during the “Delay before setting the error” time.
823 823  
1735224942262-497.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -19.9 KB
Content
1735225207687-430.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -23.0 KB
Content