Skip to Content

Changes for page 4. Firmware update

Last modified by Admin on 2025/03/03 13:18
From version 18.1
edited by Admin
on 2025/03/03 13:06
Change comment: There is no comment for this version
To version 10.2
edited by Admin
on 2024/12/04 10:52
Change comment: Update document after refactoring.

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -Battery management systems.BMS Main 2\.1.WebHome
1 +drafts.BMS Main 2\.1.WebHome
Content
... ... @@ -1,8 +1,5 @@
1 -(% data-numbered-headings-start="4" style="--numbered-headings-start: 3;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
2 -= Firmware update =
1 +== 1. Introduction ==
3 3  
4 -== Introduction ==
5 -
6 6  This document describes the steps for updating the BMS Main 2.x firmware.
7 7  
8 8  Updating the BMS Main 2.x firmware can be done in the following ways:
... ... @@ -10,7 +10,7 @@
10 10  * using ElectricDeviceMonitor via Ethernet, CAN or RS-485 bus;
11 11  * using the device web interface via Ethernet or Wi-Fi.
12 12  
13 -== Updating via ElectricDeviceMonitor ==
10 +== 2. Updating via ElectricDeviceMonitor ==
14 14  
15 15  The following hardware and software are required:
16 16  
... ... @@ -24,7 +24,7 @@
24 24  * starting the bootloader;
25 25  * uploading the firmware file to the BMS Main 2.x flash memory.
26 26  
27 -=== Start the device bootloader ===
24 +==== 2.1. Start the device bootloader ====
28 28  
29 29  * **via Web Interface**: go to the "Service → Device" section and click on the link "Reset device and start loader":
30 30  
... ... @@ -43,7 +43,7 @@
43 43  The bootloader will be active for 45 seconds. After this time, control will be transferred again to the main firmware.
44 44  )))
45 45  
46 -=== Upload the firmware ===
43 +==== 2.2. Upload the firmware. ====
47 47  
48 48  ~1. Launch the ElectricDeviceMonitor’s Updater module:
49 49  
... ... @@ -61,15 +61,15 @@
61 61  
62 62  [[image:1732877027638-368.png||data-xwiki-image-style-alignment="center"]]
63 63  
64 -* **RS-485 connection**: select the connection method “Serial port transport”, click the “Settings...” button. In the window that appears, select the COM port through which the PC connects to the device, and specify the baud rate (set up in BMS settings):
61 +* **RS-485 connection**: select the connection method “Serial port transport”, click the “Settings...” button. In the window that appears, select the COM port through which the PC connects to the device, and specify the baud rate for the COM port:
65 65  
66 -[[image:1741006734310-418.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true"]]
63 +[[image:1732877039628-104.png||data-xwiki-image-style-alignment="center"]]
67 67  
68 -3. Click the "Browse..." button and select the *.srec file with the BMS Main 2.1 firmware.
65 +3. Click the "Browse..." button and select the *.srec file with the main firmware.
69 69  
70 70  4. Click the “Update” button **while the device is in bootloader mode**. The process of loading the new firmware into the device memory will begin.
71 71  
72 -== Updating via WEB interface ==
69 +== 3. Updating via WEB interface ==
73 73  
74 74  (% class="box warningmessage" %)
75 75  (((
1741006696516-394.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -6.9 KB
Content
1741006734310-418.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -6.9 KB
Content