| Name | Abbr. | Description | Compability with discrete inputs | CANopen SDO | Modbus |
|---|
| Mini S / Mini | Main 2.1 | Main 3 |
|---|
| Balancing request | BR | a request to balance the cells; | Yes | Yes | Yes | | |
| Battery cover | CVR | a signal from the battery cover; | Yes | Yes | Yes | | |
| CH contactor feedback | CCF | a signal from charging contactor feedback loop; | Yes* | Yes | Yes | | |
| CH/DCH contactor feedback | CDF | a signal from charging/discharging contactor feedback loop; | Yes* | Yes | Yes | | |
| Charge request | CRE | a request to close the charging contactor; | Yes | Yes | Yes | | |
| Charger connected | CON | a signal indicating that charger is connected; | Yes | Yes | Yes | | |
| Circuit breaker status | CBS | status of protection disconnector; | Yes | Yes | Yes | | |
| Close External 1 | CE1 | a request to close the External 1 discrete output (if assigned). | Yes | Yes | Yes | | |
| Close Main contactor | CMC | a request to close the main contactor; | Yes | Yes | Yes | | |
| DCH contactor feedback | DCF | a signal from discharging contactor feedback loop; | Yes* | Yes | Yes | | |
| Discharge request | DRE | a request to close the discharging contactor; | Yes | Yes | Yes | | |
| Fuse 1 | F1 | signal from fuse 1; | Yes | Yes | Yes | | |
| Fuse 2 | F2 | signal from fuse 2; | Yes | Yes | Yes | | |
| Fuse 3 | F3 | signal from fuse 3; | Yes | Yes | Yes | | |
| Inhibit charging | ICH | a command to open the charging contactor; | Yes | Yes | Yes | | |
| Inhibit discharging | IDC | a command to open the discharging contactor; | Yes | Yes | Yes | | |
| Insulation status | INS | a signal from an insulation monitoring device; | Yes | Yes | Yes | | |
| Interlock | | a signal from interlock loop; | Yes | Yes | Yes | | |
| Main contactor feedback | MCF | a signal from main contactor feedback loop; | Yes* | Yes | Yes | | |
| PCH contactor feedback | PCF | a signal from precharging contactor feedback loop; | Yes* | Yes | Yes | | |
| Power up/down request | PDN | a request to power down the device; | Yes | Yes | Yes | | |
| Precharge request | PRE | a request to close the precharging contactor | Yes | Yes | | | |
| Name | Abbr. | Description | Compability | CANopen SDO | Modbus |
|---|
| Mini S / Mini | Main 2.1 | Main 3 |
|---|
| Allow charging | ACH | a signal for a charger to start charging; | Yes | Yes | Yes | | |
| Balancing 1 | BA1 | balancing the first series of cells; | | Yes | Yes | | |
| Balancing 2 | BA2 | balancing the second series of cells; | | Yes | Yes | | |
| Cell analysis | CEA | | Yes | Yes | Yes | | |
| Charging current present | CCP | the presence of the charging current; | Yes | Yes | Yes | | |
| Charging | CH | state of the charging contactor; | Yes | Yes | Yes | | |
| Charging/discharging | C/D | state of the charging/discharging contactor; | Yes | Yes | Yes | | |
| Cooler | COO | a command to turn on a cooler; | Yes | Yes | Yes | | |
| Crown EWS | EWS | | Yes | Yes | Yes | | |
| Discharging (AUX) | AUX | state of the auxiliary discharging contactor; | Yes | Yes | Yes | | |
| Discharging current present | DCP | the presence of the discharging current; | Yes | Yes | Yes | | |
| Discharging | DCH | state of the discharging contactor; | Yes | Yes | Yes | | |
| External 1 | EX1 | a signal that activates by the remote request. | | Yes | Yes | | |
| Heater | HEA | a command to turn on a heater; | Yes | Yes | Yes | | |
| Heater (AUX) | HA | | | Yes | Yes | | |
| High charging current | HCC | charging current is high; | Yes | Yes | Yes | | |
| Init | INI | | Yes | Yes | Yes | | |
| Low SOC | LOS | a signal corresponding the low SOC of the battery; | Yes | Yes | Yes | | |
| Main contactor | MCO | state of the main contactor; | Yes | Yes | Yes | | |
| Power down ACK | PDA | an acknowledgement of BMS power down. Acknowledgement is outputted when the charge and discharge contactors have been opened on power down request; | Yes | Yes | Yes | | |
| Power up | PUP | an indication of BMS power status; | Yes | Yes | Yes | | |
| Precharging | PRE | state of the precharging contactor; | Yes | Yes | Yes | | |
| Ready to charge | RTC | the battery is ready to be charged; | Yes | Yes | Yes | | |
| Ready to discharge | RTD | the battery is ready to be discharged; | Yes | Yes | Yes | | |
| Service reset | SR | | Yes | | Yes | | |
| Shutdown request (Combilift) | CSH | | Yes | Yes | Yes | | |
| Shutdown request (HYG/Spirit) | HSH | | Yes | Yes | Yes | | |
| Voltage too high for charging | ENV | | Yes | Yes | Yes | | |
| Name | Abbr. | Description | Is a Critical error? | Compability | CANopen SDO | Modbus |
| Mini S / Mini | Main 2.1 | Main 3 |
|---|
| ADC error | ADC | current cannot be measured; | • | Yes | Yes | Yes | | |
| Battery cover error | BC | battery cover is open; | • | Yes | Yes | Yes | | |
| Cell count error | CEL | number of cells does not match the specified value; | • | Yes | Yes | Yes | | |
| CH contactor cycles error | CCC | switching frequency of the charging contactor is too high; | | Yes | Yes | Yes | | |
| CH contactor feedback error | CCF | the control signals for the charging contactor and the contactor feedback differ; | • | | Yes | | | |
| CH/DCH contactor feedback error | CDF | the control signals for the charging/discharging contactor and the contactor feedback differ; | • | | Yes | | | |
| Combilift offline | COM | connection with a Combilift forklift is lost; | | Yes | Yes | Yes | | |
| Contactor feedback error | CFE | Failure of one of the contactors feedback signal. Which contactor is failed can be | | Yes | | Yes | | |
| Critical error | CER | | | Yes | Yes | Yes | | |
| Crown error | CRO | connection with a Crown forklift is lost; | | Yes | Yes | Yes | | |
| Current limit error | CLE | charging or discharging current is more than limit calculated by Charge map or Discharge map. | | Yes | | Yes | | |
| Current sensor error | CSE | error in the current sensor circuit; | • | Yes | Yes | Yes | | |
| DCH contactor cycles error | DCC | switching frequency of the discharging contactor is too high; | | Yes | Yes | Yes | | |
| DCH contactor feedback error | DCF | the control signals for the discharging contactor and the contactor feedback differ; | • | | Yes | | | |
| FS error | FSE | | | Yes | Yes | Yes | | |
| General error | GE | | | Yes | Yes | Yes | | |
| High contactor temperature | CHT | | | Yes | Yes | Yes | | |
| High humidity | HH | humidity of the battery is increased; | | Yes | Yes | Yes | | |
| High Logic temperature | LHT | at least one of the Logic devices is overheated; | | Yes | Yes | Yes | | |
| High temperature (CH) | HCT | temperature is too high for charging; | | Yes | Yes | Yes | | |
| High temperature (DCH) | HDT | temperature is too high for discharging; | | Yes | Yes | Yes | | |
| High voltage fault | HVF | failure of high voltage measuring circuits; | • | | | Yes | | |
| HVIL error | HE | breakage of high-voltage interlock current loop; | • | | | Yes | | |
| HYG offline | HYG | connection with a HYG forklift is lost; | | Yes | Yes | Yes | | |
| Insulation fault; | INF | | • | Yes | Yes | Yes | | |
| Logic count error | LOG | | | | | | | |
| Logic offline | LOF | at least one of the Logic devices is offline; | • | Yes | Yes | Yes | | |
| Low temperature (CH) | LCT | temperature is too low for charging; | | Yes | Yes | Yes | | |
| Low temperature (DCH) | LDT | temperature is too low for discharging; | | Yes | Yes | Yes | | |
| Main contactor feedback error | MCF | the control signals for the main contactor and the contactor feedback differ; | • | | Yes | | | |
| Mount error | MNT | | | Yes | Yes | Yes | | |
| Need acknowledge | ACK | there is an unacknowledged error in Error journal; | | Yes | Yes | Yes | | |
| No temperature sensors | NTS | the device has no temperature sensors connected; | • | Yes | Yes | Yes | | |
| Overcurrent | OC | | | Yes | Yes | Yes | | |
| Overvoltage | OV | | | Yes | Yes | Yes | | |
| PCH contactor feedback error | PCF | the control signals for the precharging contactor and the contactor feedback differ; | • | | Yes | | | |
| Power fault | PF | external devices power supply error: current sensors, HVIL, BMS Logic or CAN2 (int) bus powered devices; | • | | | Yes | | |
| Power switch error | PSE | short circuit in contactor coil control circuit or power switch overheating; | • | | | Yes | | |
| Precharge error | PE | capacitive load pre-charge process did not end during the estimated time; | | Yes | Yes | Yes | | |
| Settings error | SET | | | | | | | |
| Short circuit | SHC | | | Yes | Yes | Yes | | |
| Shunt error | SHE | internal error of the shunt current sensor; | • | Yes | Yes | Yes | | |
| Shunt offline | SHO | connection with the shunt current sensor is lost; | • | Yes | Yes | Yes | | |
| Spirit offline | SPI | connection with a Spirit forklift is lost; | | Yes | Yes | Yes | | |
| Stuck contactor | STC | | • | Yes | Yes | Yes | | |
| Temperature sensor is shorted | TSS | some temperature sensors are shorted; | • | Yes | Yes | Yes | | |
| Unallowable charging | UCH | charging the battery through the discharging contactor; | | Yes | Yes | Yes | | |
| Undervoltage | UV | | | Yes | Yes | Yes | | |
| Water | WA | there is water in the battery enclosure; | • | Yes | Yes | Yes | | |
| WDT reset | WDT | watchdog timer reset the device; | • | Yes | Yes | Yes | | |
