Changes for page 1. Battery controllers: signals and errors

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -65,10 +65,52 @@
65	65	Here is the list of error of BMS Main 3.
66	66
67	67
68		-|(((
69		-(% style="width:1227px" %)
70		-|(% colspan="1" rowspan="2" style="width:216px" %)**Name**|(% colspan="1" rowspan="2" style="width:321px" %)**Description**|(% colspan="1" rowspan="2" style="width:258px" %)**Set up by**|(% rowspan="2" style="width:258px" %)**Used by**
71		-)))| |
	68	+|Name |Description|Set up by|Used by|
	69	+|Overcurrent| | | |
	70	+|Undervoltage| | | |
	71	+|Overvoltage| | | |
	72	+|Low temperature (DCH) | temperature is too low for discharging;| | |
	73	+|High temperature (DCH) | temperature is too high for discharging;| | |
	74	+|Battery cover error | battery cover is open;| | |
	75	+|High humidity | humidity of the battery is increased;| | |
	76	+|Water | there is water in the battery enclosure;| | |
	77	+|High Logic temperature | at least one of the Logic devices is overheated;| | |
	78	+|Logic offline | at least one of the Logic devices is offline;| | |
	79	+|Critical error;| | | |
	80	+|Crown error | connection with a Crown forklift is lost;| | |
	81	+|Cell count error | number of cells does not match the specified value;| | |
	82	+|HYG offline | connection with a HYG forklift is lost;| | |
	83	+|Need acknowledge | there is an unacknowledged error in Error journal;| | |
	84	+|Combilift offline | connection with a Combilift forklift is lost;| | |
	85	+|Short circuit| | | |
	86	+|High contactor temperature| | | |
	87	+|ADC error | current cannot be measured;| | |
	88	+|Current sensor error | error in the current sensor circuit;| | |
	89	+|CH contactor cycles error | switching frequency of the charging contactor is too high;| | |
	90	+|DCH contactor cycles error | switching frequency of the discharging contactor is too high;| | |
	91	+|Shunt offline | connection with the shunt current sensor is lost;| | |
	92	+|Shunt error | internal error of the shunt current sensor;| | |
	93	+|WDT reset | watchdog timer reset the device;| | |
	94	+|No temperature sensors | the device has no temperature sensors connected;| | |
	95	+|Temperature sensor is shorted | some temperature sensors are shorted;| | |
	96	+|Spirit offline | connection with a Spirit forklift is lost;| | |
	97	+|Low temperature (CH) | temperature is too low for charging;| | |
	98	+|High temperature (CH) | temperature is too high for charging;| | |
	99	+|Unallowable charging | charging the battery through the discharging contactor;| | |
	100	+|Stuck contactor;| | | |
	101	+|CH contactor feedback error | the control signals for the charging contactor and the contactor feedback differ;| | |
	102	+|DCH contactor feedback error | the control signals for the discharging contactor and the contactor feedback differ;| | |
	103	+|Insulation fault;| | | |
	104	+|PCH contactor feedback error | the control signals for the precharging contactor and the contactor feedback differ;| | |
	105	+|CH/DCH contactor feedback error | the control signals for the charging/discharging contactor and the contactor feedback differ;| | |
	106	+|Main contactor feedback error | the control signals for the main contactor and the contactor feedback differ;| | |
	107	+|General error| | | |
	108	+|High voltage fault | failure of high voltage measuring circuits;| | |
	109	+|Power switch error | short circuit in contactor coil control circuit or power switch overheating;| | |
	110	+|HVIL error | breakage of high-voltage interlock current loop;| | |
	111	+|Precharge error | capacitive load pre-charge process did not end during the estimated time;| | |
	112	+|Power fault | external devices power supply error: current sensors, HVIL, BMS Logic or CAN2 (int) bus powered devices;| | |
	113	+|Current limit error | charging or discharging current is more than limit calculated by Charge map or Discharge map.| | |
72	72	| | | | |
73	73	| | | | |
74	74	| | | | |