Skip to Content

Changes for page BMS Mini S / BMS Mini

Last modified by Admin on 2025/04/14 10:53
From version 6.1
edited by Admin
on 2024/12/11 13:13
Change comment: There is no comment for this version
To version 11.2
edited by Admin
on 2025/02/27 12:57
Change comment: Update document after refactoring.

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -BMS Mini S / BMS Mini 2
1 +bms-mini
Content
... ... @@ -1,6 +1,46 @@
1 +(% class="box infomessage" %)
2 +(((
3 +BMS Mini S / BMS Mini firmware update procedure is described [[here>>doc:Battery management systems.BMS Mini S.5\. Firmware update.WebHome]].
4 +)))
5 +
6 += v1.6.1 =
7 +
8 +[[BMS_Mini_v1.6.1.srec>>FileManager.BMS_Mini_v1\.6\.1\.srec]]
9 +
10 +== Improvements ==
11 +
12 +* ability to exclude errors from being saved in the error journal (see the "Service - Errors journal" section)
13 +* extension of the CANopen dictionary to provide additional information for the BMS Display (device serial number, battery serial number, IP address in Wi-Fi network, etc.)
14 +
15 +== Fixes ==
16 +
17 +* small internal fixes
18 +
19 += v1.6.0 =
20 +
1 1  (% class="wikigeneratedid" %)
2 -BMS Mini S / BMS Mini 2 firmware update procedure is described [[here>>doc:Battery management systems.BMS Mini S.5\. Firmware update.WebHome]].
22 +[[BMS_Mini_v1.6.0.srec>>FileManager.BMS_Mini_v1\.6\.0\.srec]]
3 3  
24 +== Features ==
25 +
26 +* new parameter for setting the condition for starting balancing: automatically (regardless of the command) or on the balancing request (see the "Control - Cell balancing" section)
27 +* new option to start balancing if the cell voltage exceeds the "Voltage for forced balancing" value (see the "Control - Cell balancing" section)
28 +* new Max-Min algorithm for calculating the final battery SOC in the "Control - SOC estimation" section
29 +* new flags in the "Protections - Undervoltage" and "Protections - Overvoltage" sections which allow using the calculated open circuit cell voltage instead of the actual voltage to detect the "Undervoltage" and "Overvoltage" errors, respectively
30 +* ability to check the "Ready to charge" and "Ready to discharge" signals to control the charging and discharging contactors (see the "Control - Charge" and "Control - Discharge" sections)
31 +* improved control of the precharging contactor, which can precharge capacitive load using multiple attempts and detect high power dissipated in the precharge resistor (see the "Control - Precharge" section)
32 +* ability to select errors that the device saves in the errors journal (see the "Service - Errors journal" section)
33 +* new parameter that limits the number of battery cycles; when the number of battery cycles exceeds the limit, the BMS cannot close the charging and discharging contactors (see the "Service" section, log in under the service account)
34 +
35 +== Improvements ==
36 +
37 +* placing the device input signals to the "Battery" section and adding raw discrete inputs to the "Signals" section
38 +
39 +== Fixes ==
40 +
41 +* using the calculated open circuit voltage to set/clear the "Ready to charge" and "Ready to discharge" signals
42 +* resolving the problem of incorrect software signal addresses in the Modbus holding register table
43 +
4 4  = v1.5.1 =
5 5  
6 6  [[BMS_Mini_v1.5.1.srec>>FileManager.BMS_Mini_v1\.5\.1\.srec]]