Skip to Content

Changes for page BMS Mini S / BMS Mini

Last modified by Admin on 2026/08/06 14:53
From version 22.1
edited by Admin
on 2026/08/06 14:53
Change comment: There is no comment for this version
To version 16.1
edited by Admin
on 2025/11/10 08:12
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,63 +1,8 @@
1 1  (% class="box infomessage" %)
2 2  (((
3 -BMS Mini S / BMS Mini firmware update procedure is described [[here>>doc:Battery management systems.BMS Mini S.6\. Firmware update.WebHome]].
3 +BMS Mini S / BMS Mini firmware update procedure is described [[here>>doc:Battery management systems.BMS Mini S.5\. Firmware update.WebHome]].
4 4  )))
5 5  
6 -= v1.11.0 =
7 -
8 -[[BMS_Mini_v1.11.0.srec>>FileManager.BMS_Mini_v1\.11\.0\.srec]]
9 -
10 -== Features ==
11 -
12 -* compressing CLI responses for some commands to speed up data exchange over slow interfaces
13 -* support for the Furuisi charger (see the "External equipment - Chargers - Furuisi charger" section)
14 -
15 -== Improvements ==
16 -
17 -* deleting old log files when the SD card is full (see the corresponding flag in the "Service - SD card" section)
18 -* new CAN bus speed is not applied until the device is rebooted
19 -* improved internal current consumption measurement accuracy
20 -
21 -== Fixes ==
22 -
23 -* resolving the issue with the MicroPower charger
24 -* removed support for the BMS Wi-Fi v1
25 -
26 -= v1.10.1 =
27 -
28 -[[BMS_Mini_v1.10.1.srec>>FileManager.BMS_Mini_v1\.10\.1\.srec]]
29 -
30 -== Improvements ==
31 -
32 -* calculating the remaining time until the battery is completely discharged or fully charged
33 -
34 -= v1.10.0 =
35 -
36 -[[BMS_Mini_v1.10.0.srec>>doc:FileManager.BMS_Mini_v1\.10\.0\.srec]]
37 -
38 -== Features ==
39 -
40 -* new flag to start the heater only if the "Charger connected" signal is set (see the "Control - Heater" section)
41 -* new profile section with global battery status, which includes total energy counters, total operating time, contactor switching count, etc. (see the "Profile" tab in the Unified monitor)
42 -* new error "High board temperature" which is generated when the device overheats (see the "Protection - High board temperature" section)
43 -* support for sending battery state and events via MQTT protocol via Wi-Fi or cellular network (see the "Service - MQTT" section)
44 -* support for the BMS GSM v2 cellular module
45 -
46 -= v1.9.0 =
47 -
48 -[[BMS_Mini_v1.9.0.srec>>FileManager.BMS_Mini_v1\.9\.0\.srec]]
49 -
50 -== Features ==
51 -
52 -* support for Svyateco Drive dashboard (see the "External equipment - Trucks and Vehicles - Svyateco Drive" section)
53 -* new flag that forces the "Ready to discharge" signal to clear when the "Low SOC" signal is generated (see the "Control - Discharging status" section)
54 -* new input signal "Close External 2" which generates the new internal signal "External 2" which can be assigned to a discrete output or a power switch (see the "Signals - Input discrete signals - Assignments", "Signals - Output discrete signals - Assignments", and "Signals - Power switches - Assignments" sections)
55 -* ability to configure the generation of "External 1" and "External 2" signals based on other internal signals as an alternative to the "Close External 1" and "Close External 2" commands (see the "Signals - External 1-2 signals" section)
56 -
57 -== Fixes ==
58 -
59 -* resolving the problem of charge, discharge, and charge/discharge contactors closing when the "Precharge request" signal is set
60 -
61 61  = v1.8.0 =
62 62  
63 63  [[BMS_Mini_v1.8.0.srec>>FileManager.BMS_Mini_v1\.8\.0\.srec]]