Skip to Content

Changes for page BMS Mini S / BMS Mini

Last modified by Admin on 2026/05/06 12:17
From version 21.1
edited by Admin
on 2026/05/06 12:17
Change comment: There is no comment for this version
To version 16.2
edited by Admin
on 2026/01/30 09:33
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,42 +1,22 @@
1 1  (% class="box infomessage" %)
2 2  (((
3 -BMS Mini S / BMS Mini firmware update procedure is described [[here>>doc:Battery management systems.BMS Mini S.6\. Firmware update.WebHome]].
3 +BMS Mini S / BMS Mini firmware update procedure is described [[here>>doc:Battery management systems.BMS Mini S.5\. Firmware update.WebHome]].
4 4  )))
5 5  
6 -= v1.10.1 =
7 -
8 -[[BMS_Mini_v1.10.1.srec>>FileManager.BMS_Mini_v1\.10\.1\.srec]]
9 -
10 -== Improvements ==
11 -
12 -* calculating the remaining time until the battery is completely discharged or fully charged
13 -
14 -= v1.10.0 =
15 -
16 -[[BMS_Mini_v1.10.0.srec>>doc:FileManager.BMS_Mini_v1\.10\.0\.srec]]
17 -
18 -== Features ==
19 -
20 -* new flag to start the heater only if the "Charger connected" signal is set (see the "Control - Heater" section)
21 -* new profile section with global battery status, which includes total energy counters, total operating time, contactor switching count, etc. (see the "Profile" tab in the Unified monitor)
22 -* new error "High board temperature" which is generated when the device overheats (see the "Protection - High board temperature" section)
23 -* support for sending battery state and events via MQTT protocol via Wi-Fi or cellular network (see the "Service - MQTT" section)
24 -* support for the BMS GSM v2 cellular module
25 -
26 26  = v1.9.0 =
27 27  
28 28  [[BMS_Mini_v1.9.0.srec>>FileManager.BMS_Mini_v1\.9\.0\.srec]]
29 29  
30 -== Features ==
10 +Features
31 31  
32 -* support for Svyateco Drive dashboard (see the "External equipment - Trucks and Vehicles - Svyateco Drive" section)
33 -* new flag that forces the "Ready to discharge" signal to clear when the "Low SOC" signal is generated (see the "Control - Discharging status" section)
34 -* new input signal "Close External 2" which generates the new internal signal "External 2" which can be assigned to a discrete output or a power switch (see the "Signals - Input discrete signals - Assignments", "Signals - Output discrete signals - Assignments", and "Signals - Power switches - Assignments" sections)
35 -* ability to configure the generation of "External 1" and "External 2" signals based on other internal signals as an alternative to the "Close External 1" and "Close External 2" commands (see the "Signals - External 1-2 signals" section)
12 +support for Svyateco Drive dashboard (see the "External equipment - Trucks and Vehicles - Svyateco Drive" section)
13 +new flag that forces the "Ready to discharge" signal to clear when the "Low SOC" signal is generated (see the "Control - Discharging status" section)
14 +new input signal "Close External 2" which generates the new internal signal "External 2" which can be assigned to a discrete output or a power switch (see the "Signals - Input discrete signals - Assignments", "Signals - Output discrete signals - Assignments", and "Signals - Power switches - Assignments" sections)
15 +ability to configure the generation of "External 1" and "External 2" signals based on other internal signals as an alternative to the "Close External 1" and "Close External 2" commands (see the "Signals - External 1-2 signals" section)
36 36  
37 -== Fixes ==
17 +Fixes
38 38  
39 -* resolving the problem of charge, discharge, and charge/discharge contactors closing when the "Precharge request" signal is set
19 +resolving the problem of charge, discharge, and charge/discharge contactors closing when the "Precharge request" signal is set
40 40  
41 41  = v1.8.0 =
42 42