Skip to Content

Changes for page BMS Mini S / BMS Mini

Last modified by Admin on 2025/04/14 10:53
From version 12.1
edited by Admin
on 2025/02/27 12:57
Change comment: There is no comment for this version
To version 6.1
edited by Admin
on 2024/12/11 13:13
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -BMS Mini S / BMS Mini
1 +BMS Mini S / BMS Mini 2
Content
... ... @@ -1,46 +21,6 @@
1 -(% class="box infomessage" %)
2 -(((
3 -BMS Mini S / BMS Mini firmware update procedure is described [[here>>doc:Battery management systems.BMS Mini S.5\. Firmware update.WebHome]].
4 -)))
5 -
6 -= v1.6.1 =
7 -
8 -[[BMS_Mini_v1.6.1.srec>>FileManager.BMS_Mini_v1\.6\.1\.srec]]
9 -
10 -== Improvements ==
11 -
12 -* ability to exclude errors from being saved in the error journal (see the "Service - Errors journal" section)
13 -* extension of the CANopen dictionary to provide additional information for the BMS Display (device serial number, battery serial number, IP address in Wi-Fi network, etc.)
14 -
15 -== Fixes ==
16 -
17 -* small internal fixes
18 -
19 -= v1.6.0 =
20 -
21 21  (% class="wikigeneratedid" %)
22 -[[BMS_Mini_v1.6.0.srec>>FileManager.BMS_Mini_v1\.6\.0\.srec]]
2 +BMS Mini S / BMS Mini 2 firmware update procedure is described [[here>>doc:Battery management systems.BMS Mini S.5\. Firmware update.WebHome]].
23 23  
24 -== Features ==
25 -
26 -* new parameter for setting the condition for starting balancing: automatically (regardless of the command) or on the balancing request (see the "Control - Cell balancing" section)
27 -* new option to start balancing if the cell voltage exceeds the "Voltage for forced balancing" value (see the "Control - Cell balancing" section)
28 -* new Max-Min algorithm for calculating the final battery SOC in the "Control - SOC estimation" section
29 -* new flags in the "Protections - Undervoltage" and "Protections - Overvoltage" sections which allow using the calculated open circuit cell voltage instead of the actual voltage to detect the "Undervoltage" and "Overvoltage" errors, respectively
30 -* ability to check the "Ready to charge" and "Ready to discharge" signals to control the charging and discharging contactors (see the "Control - Charge" and "Control - Discharge" sections)
31 -* improved control of the precharging contactor, which can precharge capacitive load using multiple attempts and detect high power dissipated in the precharge resistor (see the "Control - Precharge" section)
32 -* ability to select errors that the device saves in the errors journal (see the "Service - Errors journal" section)
33 -* new parameter that limits the number of battery cycles; when the number of battery cycles exceeds the limit, the BMS cannot close the charging and discharging contactors (see the "Service" section, log in under the service account)
34 -
35 -== Improvements ==
36 -
37 -* placing the device input signals to the "Battery" section and adding raw discrete inputs to the "Signals" section
38 -
39 -== Fixes ==
40 -
41 -* using the calculated open circuit voltage to set/clear the "Ready to charge" and "Ready to discharge" signals
42 -* resolving the problem of incorrect software signal addresses in the Modbus holding register table
43 -
44 44  = v1.5.1 =
45 45  
46 46  [[BMS_Mini_v1.5.1.srec>>FileManager.BMS_Mini_v1\.5\.1\.srec]]