Skip to Content

Changes for page BMS Main X

Last modified by Admin on 2025/07/22 11:39
From version 8.1
edited by Admin
on 2025/07/22 11:39
Change comment: There is no comment for this version
To version 1.2
edited by Admin
on 2024/11/22 09:00
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,102 +100,3 @@
1 -(% class="box infomessage" %)
2 -(((
3 -BMS Main X firmware update procedure is described [[here>>doc:Battery management systems.BMS Main X.5\. Firmware update.WebHome]].
4 -)))
5 -
6 -= v2.8.1 =
7 -
8 -[[BMS_Main_X2_v2.8.1.srec>>FileManager.BMS_Main_X2_v2\.8\.1\.srec]]
9 -
10 -== Improvements ==
11 -
12 -* new CLI command "find-log" which finds a log file containing a specified timestamp
13 -* ability to acknowledge battery module errors via CLI (see the "Service - Errors journal" section) and Modbus protocol
14 -
15 -== Fixes ==
16 -
17 -* resolving the issue of rebooting the device if formatting the SD card is activated
18 -
19 -= v2.8.0 =
20 -
21 -[[BMS_Main_X2_v2.8.0.srec>>FileManager.BMS_Main_X2_v2\.8\.0\.srec]]
22 -
23 -== Features ==
24 -
25 -* new flags that allow to interrupt (shorten) the module balancing stage if all battery modules are already joined (see the "Control - Charge", "Control - Discharge", "Control - Charge/Discharge" sections)
26 -* forwarding CLI and bootloader CAN messages from CAN EXT interface to CAN INT interface and back
27 -* new parameter for setting the type of network to which the BMS GSM communication module connects (see the "Connectivity - Cellular" section)
28 -* new flag that controls whether to use open circuit voltage or actual voltage when determining the voltage unbalance error (see the "Protections - Voltage unbalance (in any state)" section)
29 -* new regulator that maintains battery current limiting to ensure that actual module currents do not exceed their current limits (see the "Control - Charge", "Control - Discharge", "Control - Charge/Discharge" sections)
30 -* ability to select the battery module errors that cause the battery critical error (see the "Protections - Critical error" section)
31 -* ability to update the device serial number from the service account if the number is reset to the default value for some reason (see the "Service" section)
32 -
33 -== Improvements ==
34 -
35 -* dynamic calculation of data transfer schedule for optimal communication with a large number of battery modules
36 -* ability to complete device initialization after the set timeout has expired and the minimum number of modules has been detected (see the "Control - Initialization" section)
37 -* 30 second delay when remounting SD card after detecting mount error
38 -* saving the number of joined modules in log files
39 -
40 -== Fixes ==
41 -
42 -* resolving the issue of saving some battery module signals in log files
43 -
44 -= v2.7.0 =
45 -
46 -[[BMS_Main_X2_v2.7.0.srec>>FileManager.BMS_Main_X2_v2\.7\.0\.srec]]
47 -
48 -== Features ==
49 -
50 -* new algorithm in the Charging/Discharging controller that allow to control the Charging/Discharging contactor independently from the Charging and Discharging signals (see the "Control - Charge/Discharge" section). The new "Independent" algorithm is preferred in the battery systems with one contactor
51 -* new "Need acknowledge" warning signal that is set when a new record is created in the errors journal. The signal can be cleared in the "Service - Errors journal" section
52 -* new Max-Min algorithm for calculating the final battery SOC in the "Control - Calculation" section
53 -* improved control of the precharging contactor, which can precharge capacitive load using multiple attempts and detect high power dissipated in the precharge resistor (see the "Control - Precharge" section)
54 -* ability to exclude errors from being saved in the error journal (see the "Service - Errors journal" section)
55 -* ability to restart the device according to a specified schedule at the moment when the battery system is preparing to charge
56 -* new error "High contactor temperature" that can be used to open the specified contactor to prevent it from overheating (see the "Protections - High contactor temperature" section)
57 -* new internal signal "Coolant pump" that can be assigned to a relay or discrete output (for signal settings, see the "Control - Coolant pump" section)
58 -* new flags indicating the readiness of battery modules to join for charging and discharging (see the "Modules" section)
59 -* new flag to set the "Voltage unbalance" errors for battery modules that are not ready to charge or discharge (see the "Protections - Voltage unbalance (in any state)" section)
60 -* initial support for Pylontech inverters
61 -* extension of the CANopen dictionary to provide additional information for the BMS Display (device serial number, battery serial number, battery address, Wi-Fi and LAN addresses, SOH, capacity, etc.)
62 -
63 -== Improvements ==
64 -
65 -* ability to finish device initialization even if the number of battery modules found is less than the number of modules enabled (see the "Control - Modules" section)
66 -* placing the device input signals to the "Battery" section and adding raw discrete inputs to the "Signals" section
67 -
68 -== Fixes ==
69 -
70 -* resolving the issue of ignoring the minimum number of battery modules allowed to join located in the "Control - Discharge" section
71 -* resolving the issue of joining battery modules the number of which must be greater than or equal to the minimum value specified in the settings
72 -* small internal fixes
73 -
74 -= v2.6.3 =
75 -
76 -[[BMS_Main_X2_v2.6.3.srec>>FileManager.BMS_Main_X2_v2\.6\.3\.srec]]
77 -
78 -== Improvements ==
79 -
80 -* adaptation of the device to the production test bench
81 -
82 -= v2.6.2 =
83 -
84 -[[BMS_Main_X2_v2.6.2.srec>>FileManager.BMS_Main_X2_v2\.6\.2\.srec]]
85 -
86 -== Fixes ==
87 -
88 -* resolving the problem of saving device parameters
89 -
90 -= v2.6.1 =
91 -
92 -[[BMS_Main_X2_v2.6.1.srec>>FileManager.BMS_Main_X2_v2\.6\.1\.srec]]
93 -
94 -== Fixes ==
95 -
96 -* resolving the issue of preparing battery module states written to Modbus registers
97 -* resolving the problem of writing the device's working time to a non-volatile memory very often
98 -* resolving the problem of returning error states when saving device parameters (mainly via Wi-Fi)
99 -
100 100  = v2.6.0 =
101 101  
102 102  [[BMS_Main_X2_v2.6.0.srec>>FileManager.BMS_Main_X2_v2\.6\.0\.srec]]
... ... @@ -110,10 +110,6 @@
110 110  * new assignments "Charging", "Precharging", "Discharging", "Charging/Discharging", "Main contactor", "Critical error" and "General error (modules)" for the discrete outputs (see the "Signals - Output discrete signals - Assignments" section)
111 111  * new assignments "Critical error" and "General error (modules)" for the relays (see the "Signals - Relays - Assignments" section)
112 112  
113 -== Improvements ==
14 +Improvements
114 114  
115 -* rearrangements in the settings sections, which are made to simplify the setup process
116 -
117 -== Fixes ==
118 -
119 -* resolving the problem of device hanging due to high activity on the CAN bus during startup
16 +