Changes for page BMS Main 3X

Last modified by Admin on 2025/02/18 14:58

From version 9.1
edited by Admin
on 2025/02/18 14:58
Change comment: There is no comment for this version
To version 1.1
edited by Admin
on 2024/11/18 10:24
Change comment: There is no comment for this version

Summary

Details

Page properties
Tags
... ... @@ -1,1 +1,0 @@
1 -BMS Main 3X
Content
... ... @@ -1,67 +1,19 @@
1 -(% class="box infomessage" %)
2 -(((
3 -BMS Main 3X firmware update procedure is described [[here>>doc:Battery management systems.BMS Main 3.5\. Firmware update.WebHome]].
4 -)))
1 += 3.1.1 =
5 5  
6 -= v3.2.1 =
3 +...
7 7  
8 -[[BMS_Main_3X_v3.2.1.bin>>FileManager.BMS_Main_3X_v3\.2\.1\.bin]]
9 -
10 -== Improvements ==
11 -
12 -* new parameter that sets the delay before measuring the current to determine that precharge is finished (see the "Control - Precharge" section)
13 -* ability to exclude errors from being saved in the error journal (see the "Service - Errors journal" section)
14 -* new flags indicating the readiness of battery modules to join for charging and discharging (see the "Modules" section)
15 -* new flag to set the "Voltage unbalance" errors for battery modules that are not ready to charge or discharge (see the "Protections - Voltage unbalance (in any state)" section)
16 -* Unibat: new parameters setting the BMS and VCU addresses (see the "External equipment - Unibat vehicle" section)
17 -* Unibat: new flag to invert the discharge current limit sent to the vehicle (see the "External equipment - Unibat vehicle" section)
18 -* Unibat: using the difference between the maximum and minimum temperatures among all cells as an input for the coolant pump controller
19 -* Unibat: automatically switch from discharging to charging mode if the CHARGE_ON signal or the charging station command is set (without rejoining the battery)
20 -* extension of the CANopen dictionary to provide additional information for the BMS Display (device serial number, battery serial number, battery address, Wi-Fi and LAN addresses, SOH, capacity, etc.)
21 -
22 22  == Fixes ==
23 23  
24 -* resolving the issue of ignoring the minimum number of battery modules allowed to join located in the "Control - Discharge" section
25 -* resolving the issue of joining battery modules the number of which must be greater than or equal to the minimum value specified in the settings
26 -* making the service reset function work properly
27 -* small internal fixes
28 -
29 -= v3.2.0 =
30 -
31 -(% class="wikigeneratedid" %)
32 -[[BMS_Main_3X_v3.2.0.bin>>FileManager.BMS_Main_3X_v3\.2\.0\.bin]]
33 -
34 -== Features ==
35 -
36 -* new algorithm in the Charging/Discharging controller that allow to control the Charging/Discharging contactor independently from the Charging and Discharging signals (see the "Control - Charge/Discharge" section). The new "Independent" algorithm is preferred in the battery systems with one contactor
37 -* new "Need acknowledge" warning signal that is set when a new record is created in the errors journal. The signal can be cleared in the "Service - Errors journal" section
38 -* new Max-Min algorithm for calculating the final battery SOC in the "Control - Calculation" section
39 -* improved control of the precharging contactor, which can precharge capacitive load using multiple attempts and detect high power dissipated in the precharge resistor (see the "Control - Precharge" section)
40 -* ability to select errors that the device saves in the errors journal (see the "Service - Errors journal" section)
41 -
42 -== Improvements ==
43 -
44 -* ability to finish device initialization even if the number of battery modules found is less than the number of modules enabled
45 -* ability to configure and monitor the device via the CAN1 (ext) bus
46 -* placing the device input signals to the "Battery" section and adding raw discrete inputs to the "Signals" section
47 -* Unibat: support for functional description v3.5 (protocol v1.5)
48 -
49 -= v3.1.1 =
50 -
51 -[[BMS_Main_3X_v3.1.1.bin>>FileManager.BMS_Main_3X_v3\.1\.1\.bin]]
52 -
53 -== Fixes ==
54 -
55 55  * resolving the problem of incorrect range of temperature parameter values (in the "Control - Coolant pump" section)
56 56  * resolving the possible problem of saving device parameters
57 57  * resolving the problem of writing the device's working time to a non-volatile memory very often
58 58  * resolving the issue of preparing battery module states written to Modbus registers
59 59  
60 -= v3.1.0 =
12 +3.1.0
61 61  
62 -[[BMS_Main_3X_v3.1.0.bin>>FileManager.BMS_Main_3X_v3\.1\.0\.bin]]
14 +...
63 63  
64 -== Features ==
16 +Features
65 65  
66 66  * new parameter to set the minimum number of battery modules allowed to join (see the "Control - Charge" and "Control - Discharge" sections)
67 67  * ability to rejoin battery modules if their voltage is close to the battery voltage (see the "Control - Charge" and "Control - Discharge" sections)
... ... @@ -69,12 +69,8 @@
69 69  * new internal signal "General error (modules)" which is the logical sum of the "General error" signals from the battery modules
70 70  * new assignments "Critical error" and "General error (modules)" for the discrete outputs and power switches (see the "Signals - Output discrete signals - Assignments" and "Signals - Power switches - Assignments" sections)
71 71  
72 -== Improvements ==
24 +Improvements
73 73  
74 -* use the measured voltage before contactors as the battery voltage if the "Control - High voltage" function is enabled
75 -* Unibat: new flag to enable sending a control message to start/stop ventilation fans installed in the battery modules (see the "External equipment - Unibat vehicle" section)
76 -* rearrangements in the settings sections, which are made to simplify the setup process
77 -
78 -== Fixes ==
79 -
80 -* Unibat: minor changes in the communication protocol
26 +- use the measured voltage before contactors as the battery voltage if the "Control - High voltage" function is enabled
27 +- Unibat: new flag to enable sending a control message to start/stop ventilation fans installed in the battery modules (see the "External equipment - Unibat vehicle" section)
28 +- rearrangements in the settings sections, which are made to simplify the setup process