Skip to Content

Changes for page BMS Main 3X

Last modified by Admin on 2026/02/18 13:39
From version 22.1
edited by Admin
on 2026/02/05 03:31
Change comment: There is no comment for this version
To version 18.1
edited by Admin
on 2025/10/27 11:43
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,73 +1,8 @@
1 1  (% class="box infomessage" %)
2 2  (((
3 -BMS Main 3X firmware update procedure is described [[here>>doc:Battery management systems.BMS Main 3.6\. Firmware update.WebHome]].
3 +BMS Main 3X firmware update procedure is described [[here>>doc:Battery management systems.BMS Main 3.5\. Firmware update.WebHome]].
4 4  )))
5 5  
6 -= v3.8.1 =
7 -
8 -[[BMS_Main_3X_v3.8.1.bin>>FileManager.BMS_Main_3X_v3\.8\.1\.bin]]
9 -
10 -== Improvements ==
11 -
12 -* setting and clearing the "Voltage unbalance" errors without delays
13 -* new CAN bus speed is not applied until the device is rebooted
14 -* logging the following new parameters: "UnibatState", "UnibatOperationalModeState", "Keyrun", "ChargeOn"
15 -* Unibat: ability to shutdown the battery if its SOC is too low (see the "External equipment - Unibat vehicle - Diagnostic parameters" section)
16 -* Unibat: change the resolution of parameters CC and DC from 0.01 to 0.1 Ah/bit
17 -* Unibat: do not turn on the amber lamp if the actual battery SOC is equal to the configured maximum operational SOC
18 -
19 -== Fixes ==
20 -
21 -* resolving the problem of completing the initialization process before the power switch voltage stabilizes
22 -
23 -= v3.8.0 =
24 -
25 -[[BMS_Main_3X_v3.8.0.bin>>FileManager.BMS_Main_3X_v3\.8\.0\.bin]]
26 -
27 -== Features ==
28 -
29 -* support for the Trolleybat vehicle (see the "External equipment - Trolleybat vehicle" section)
30 -
31 -== Improvements ==
32 -
33 -* checking the continuous charge current limit only if the "Use continuous charge current limit" flag is set in the "External equipment - Unibat vehicle - General parameters" section
34 -* Unibat: transition to charging mode according to the condition EESCD=7
35 -
36 -== Fixes ==
37 -
38 -* resolving the problem of completing the initialization process before the power switch voltage stabilizes
39 -* Unibat: prevent the "Charge request" and "Discharge request" signals from being reset if the Unibat vehicle goes offline (the signals are controlled in the Unibat state machine)
40 -
41 -= v3.7.1 =
42 -
43 -[[BMS_Main_3X_v3.7.1.bin>>FileManager.BMS_Main_3X_v3\.7\.1\.bin]]
44 -
45 -== Fixes ==
46 -
47 -* Unibat: do not send the insulation error DTC if the IMD goes offline when the battery system is in the shutdown mode
48 -
49 -= v3.7.0 =
50 -
51 -[[BMS_Main_3X_v3.7.0.bin>>FileManager.BMS_Main_3X_v3\.7\.0\.bin]]
52 -
53 -== Features ==
54 -
55 -* new profile section with global battery status, which includes total charge and energy counters, total operating time, contactor opening count, etc. (see the "Profile" tab in the Unified monitor)
56 -* new total charge counters (plus and minus)
57 -
58 -== Improvements ==
59 -
60 -* Unibat: new flag to set the custom value (=3) for the EESCD signal (see the "External equipment - Unibat vehicle - General parameters" section)
61 -* Unibat: new bit field to ignore internal errors that cause battery shutdown (see the "External equipment - Unibat vehicle - General parameters" section)
62 -* Unibat: sending a new packet containing the continuous charge current limit
63 -
64 -== Fixes ==
65 -
66 -* optimization of the logging process, minimizing the time to open the next log file if the current one is full
67 -* resolving the stability problem when the SD card is full
68 -* Unibat: prevent sending module online statuses if the power down condition is met
69 -* Unibat: small fixes
70 -
71 71  = v3.6.2 =
72 72  
73 73  [[BMS_Main_3X_v3.6.2.bin>>FileManager.BMS_Main_3X_v3\.6\.2\.bin]]