Changes for page BMS Main 3X
Last modified by Admin on 2026/02/18 13:39
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -1,90 +1,8 @@ 1 1 (% class="box infomessage" %) 2 2 ((( 3 -BMS Main 3X firmware update procedure is described [[here>>doc:Battery management systems.BMS Main 3. 6\. Firmware update.WebHome]].3 +BMS Main 3X firmware update procedure is described [[here>>doc:Battery management systems.BMS Main 3.5\. Firmware update.WebHome]]. 4 4 ))) 5 5 6 -= v3.8.1 = 7 - 8 -[[BMS_Main_3X_v3.8.1.bin>>FileManager.BMS_Main_3X_v3\.8\.1\.bin]] 9 - 10 -== Improvements == 11 - 12 -* setting and clearing the "Voltage unbalance" errors without delays 13 -* new CAN bus speed is not applied until the device is rebooted 14 -* logging the following new parameters: "UnibatState", "UnibatOperationalModeState", "Keyrun", "ChargeOn" 15 -* Unibat: ability to shutdown the battery if its SOC is too low (see the "External equipment - Unibat vehicle - Diagnostic parameters" section) 16 -* Unibat: change the resolution of parameters CC and DC from 0.01 to 0.1 Ah/bit 17 -* Unibat: do not turn on the amber lamp if the actual battery SOC is equal to the configured maximum operational SOC 18 - 19 -== Fixes == 20 - 21 -* resolving the problem of completing the initialization process before the power switch voltage stabilizes 22 - 23 -= v3.8.0 = 24 - 25 -[[BMS_Main_3X_v3.8.0.bin>>FileManager.BMS_Main_3X_v3\.8\.0\.bin]] 26 - 27 -== Features == 28 - 29 -* support for the Trolleybat vehicle (see the "External equipment - Trolleybat vehicle" section) 30 - 31 -== Improvements == 32 - 33 -* checking the continuous charge current limit only if the "Use continuous charge current limit" flag is set in the "External equipment - Unibat vehicle - General parameters" section 34 -* Unibat: transition to charging mode according to the condition EESCD=7 35 - 36 -== Fixes == 37 - 38 -* resolving the problem of completing the initialization process before the power switch voltage stabilizes 39 -* Unibat: prevent the "Charge request" and "Discharge request" signals from being reset if the Unibat vehicle goes offline (the signals are controlled in the Unibat state machine) 40 - 41 -= v3.7.1 = 42 - 43 -[[BMS_Main_3X_v3.7.1.bin>>FileManager.BMS_Main_3X_v3\.7\.1\.bin]] 44 - 45 -== Fixes == 46 - 47 -* Unibat: do not send the insulation error DTC if the IMD goes offline when the battery system is in the shutdown mode 48 - 49 -= v3.7.0 = 50 - 51 -[[BMS_Main_3X_v3.7.0.bin>>FileManager.BMS_Main_3X_v3\.7\.0\.bin]] 52 - 53 -== Features == 54 - 55 -* new profile section with global battery status, which includes total charge and energy counters, total operating time, contactor opening count, etc. (see the "Profile" tab in the Unified monitor) 56 -* new total charge counters (plus and minus) 57 - 58 -== Improvements == 59 - 60 -* Unibat: new flag to set the custom value (=3) for the EESCD signal (see the "External equipment - Unibat vehicle - General parameters" section) 61 -* Unibat: new bit field to ignore internal errors that cause battery shutdown (see the "External equipment - Unibat vehicle - General parameters" section) 62 -* Unibat: sending a new packet containing the continuous charge current limit 63 - 64 -== Fixes == 65 - 66 -* optimization of the logging process, minimizing the time to open the next log file if the current one is full 67 -* resolving the stability problem when the SD card is full 68 -* Unibat: prevent sending module online statuses if the power down condition is met 69 -* Unibat: small fixes 70 - 71 -= v3.6.2 = 72 - 73 -[[BMS_Main_3X_v3.6.2.bin>>FileManager.BMS_Main_3X_v3\.6\.2\.bin]] 74 - 75 -== Improvements == 76 - 77 -* turning on power switches with a delay of 1 second after reaching the supply voltage of 9V 78 -* Unibat: new flag that allows to hide the insulation testing status when repeating measurements (see the "External equipment - Unibat vehicle" section) 79 -* expansion of the list of parameters that are reset to default values when the device is powered on while holding the button on the board. The following parameters are affected: all CAN1 (ext) settings; all CAN2 (int) settings; all CAN3 (BMS) settings; all RS-485-1 (Modbus) settings; LAN settings: IP mode, IP address, Netmask, Gateway address 80 - 81 -== Fixes == 82 - 83 -* resolving the issue of false warnings indicating that the battery current exceeds the current limits (affects Unibat vehicle) 84 -* Unibat: changes that make it so that the output period is responsible for only 4 messages, not for all messages (see the "External equipment - Unibat vehicle" section) 85 -* Unibat: resolving the issue of TP messages not being sent if the transport is already transmitting something at the time of the request 86 -* corrections of typos in parameter descriptions 87 - 88 88 = v3.6.1 = 89 89 90 90 [[BMS_Main_3X_v3.6.1.bin>>FileManager.BMS_Main_3X_v3\.6\.1\.bin]]