Skip to Content

Changes for page BMS Main 3X

Last modified by Admin on 2025/12/10 16:23
From version 17.1
edited by Admin
on 2025/10/06 04:50
Change comment: There is no comment for this version
To version 20.2
edited by Admin
on 2025/12/10 16:23
Change comment: Renamed back-links.

Summary

Details

Page properties
Content
... ... @@ -1,8 +1,55 @@
1 1  (% class="box infomessage" %)
2 2  (((
3 -BMS Main 3X firmware update procedure is described [[here>>doc:Battery management systems.BMS Main 3.5\. Firmware update.WebHome]].
3 +BMS Main 3X firmware update procedure is described [[here>>doc:Battery management systems.BMS Main 3.6\. Firmware update.WebHome]].
4 4  )))
5 5  
6 += v3.7.1 =
7 +
8 +[[BMS_Main_3X_v3.7.1.bin>>FileManager.BMS_Main_3X_v3\.7\.1\.bin]]
9 +
10 +== Fixes ==
11 +
12 +* Unibat: do not send the insulation error DTC if the IMD goes offline when the battery system is in the shutdown mode
13 +
14 += v3.7.0 =
15 +
16 +[[BMS_Main_3X_v3.7.0.bin>>FileManager.BMS_Main_3X_v3\.7\.0\.bin]]
17 +
18 +== Features ==
19 +
20 +* new profile section with global battery status, which includes total charge and energy counters, total operating time, contactor opening count, etc. (see the "Profile" tab in the Unified monitor)
21 +* new total charge counters (plus and minus)
22 +
23 +== Improvements ==
24 +
25 +* Unibat: new flag to set the custom value (=3) for the EESCD signal (see the "External equipment - Unibat vehicle - General parameters" section)
26 +* Unibat: new bit field to ignore internal errors that cause battery shutdown (see the "External equipment - Unibat vehicle - General parameters" section)
27 +* Unibat: sending a new packet containing the continuous charge current limit
28 +
29 +== Fixes ==
30 +
31 +* optimization of the logging process, minimizing the time to open the next log file if the current one is full
32 +* resolving the stability problem when the SD card is full
33 +* Unibat: prevent sending module online statuses if the power down condition is met
34 +* Unibat: small fixes
35 +
36 += v3.6.2 =
37 +
38 +[[BMS_Main_3X_v3.6.2.bin>>FileManager.BMS_Main_3X_v3\.6\.2\.bin]]
39 +
40 +== Improvements ==
41 +
42 +* turning on power switches with a delay of 1 second after reaching the supply voltage of 9V
43 +* Unibat: new flag that allows to hide the insulation testing status when repeating measurements (see the "External equipment - Unibat vehicle" section)
44 +* expansion of the list of parameters that are reset to default values when the device is powered on while holding the button on the board. The following parameters are affected: all CAN1 (ext) settings; all CAN2 (int) settings; all CAN3 (BMS) settings; all RS-485-1 (Modbus) settings; LAN settings: IP mode, IP address, Netmask, Gateway address
45 +
46 +== Fixes ==
47 +
48 +* resolving the issue of false warnings indicating that the battery current exceeds the current limits (affects Unibat vehicle)
49 +* Unibat: changes that make it so that the output period is responsible for only 4 messages, not for all messages (see the "External equipment - Unibat vehicle" section)
50 +* Unibat: resolving the issue of TP messages not being sent if the transport is already transmitting something at the time of the request
51 +* corrections of typos in parameter descriptions
52 +
6 6  = v3.6.1 =
7 7  
8 8  [[BMS_Main_3X_v3.6.1.bin>>FileManager.BMS_Main_3X_v3\.6\.1\.bin]]