Wiki source code of BMS Main 3

Version 10.1 by Admin on 2024/12/25 14:05

Show last authors
1 (% class="box infomessage" %)
2 (((
3 BMS Main 3 firmware update procedure is described [[here>>doc:Battery management systems.BMS Main 3.5\. Firmware update.WebHome]].
4 )))
5
6 = v2.2.0 =
7
8 [[BMS_Main_3_v2.2.0.bin>>FileManager.BMS_Main_3_v2\.2\.0\.bin]]
9
10 == Features ==
11
12 * support for the HYG Global CAN protocol version 2 (June 13, 2024)
13 * calculation of regenerated energy
14 * calculation of new lifetime parameters: average temperature, average charge/discharge currents, etc. See the counters in the "Service - Counters" section
15 * new "Need acknowledge" warning signal that is set when a new record is created in the errors journal. The signal can be cleared in the "Service - Errors journal" section
16 * new parameter for setting the condition for starting balancing: automatically (regardless of the command) or on the balancing request (see the "Control - Cell balancing" section)
17 * new option to start balancing if the cell voltage exceeds the "Voltage for forced balancing" value (see the "Control - Cell balancing" section)
18 * new Max-Min algorithm for calculating the final battery SOC in the "Control - SOC estimation" section
19 * new flags in the "Protections - Undervoltage" and "Protections - Overvoltage" sections which allow using the calculated open circuit cell voltage instead of the actual voltage to detect the "Undervoltage" and "Overvoltage" errors, respectively
20 * ability to check the "Ready to charge" and "Ready to discharge" signals to control the charging and discharging contactors (see the "Control - Charge" and "Control - Discharge" sections)
21 * improved control of the precharging contactor, which can precharge capacitive load using multiple attempts and detect high power dissipated in the precharge resistor (see the "Control - Precharge" section)
22 * ability to select errors that the device saves in the errors journal (see the "Service - Errors journal" section)
23
24 == Improvements ==
25
26 * ability to configure and monitor the device via the CAN1 (ext) bus
27 * placing the device input signals to the "Battery" section and adding raw discrete inputs to the "Signals" section
28
29 == Fixes ==
30
31 * using the calculated open circuit voltage to set/clear the "Ready to charge" and "Ready to discharge" signals
32
33 = v2.1.1 =
34
35 [[BMS_Main_3_v2.1.1.bin>>FileManager.BMS_Main_3_v2\.1\.1\.bin]]
36
37 == Improvements ==
38
39 * new balancing strategy that attempts to keep the temperature of BMS Logic devices below a set value by discharging cells with higher voltages first than others (see the "Control - Cell balancing" section)
40
41 == Fixes ==
42
43 * resolving the possible problem of saving device parameters
44 * resolving the problem of writing the device's working time to a non-volatile memory very often
45
46 = v2.1.0 =
47
48 [[BMS_Main_3_v2.1.0.bin>>FileManager.BMS_Main_3_v2\.1\.0\.bin]]
49
50 == Features ==
51
52 * new algorithms in the Charging/Discharging controller that allow to control the Charging/Discharging contactor independently from the Charging and Discharging signals (see the "Control - Charge/Discharge" section). The new "Independent" algorithms are preferred in the battery systems with one contactor.
53 * selection of errors that cause reset of contactor control signals (see the "Control - Main contactor", "Control - Charge", "Control - Discharge", "Control - Charge/Discharge", "Control - Discharge (AUX)", "Control - Heater", "Control - Cooler", "Protections - General error", "Control - Charging status", "Control - Discharging status" sections)
54 * new "Current limit error" which is set if the battery current exceeds the charging or discharging current limits (see the "Protections - Charge current limit" and "Protections - Discharge current limit" sections)
55 * new parameter to select the method of calculating the battery voltage: sum the cell voltages or use the measured voltage before contactors (see the "Control - Common settings" section)
56 * clearing the Discharging (AUX) signal if the cell voltage is too low (see the "Control - Discharge (AUX)" section)
57 * new assignment "Close External 1" for the discrete inputs (see the "Signals - Input discrete signals - Assignments" section)
58 * new assignment "External 1" for the discrete outputs and power switches (see the "Signals - Output discrete signals - Assignments" and "Signals - Power switches - Assignments" sections). The "External 1" output is directly controlled by the "Close External 1" command.
59
60 == Improvements ==
61
62 * rearrangements in the settings sections, which are made to simplify the setup process