Skip to Content

Changes for page BMS Main 3

Last modified by Admin on 2025/04/15 09:56
From version 7.1
edited by Admin
on 2024/12/11 13:10
Change comment: There is no comment for this version
To version 14.1
edited by Admin
on 2025/04/15 09:56
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,6 +1,71 @@
1 -(% class="wikigeneratedid" %)
1 +(% class="box infomessage" %)
2 +(((
2 2  BMS Main 3 firmware update procedure is described [[here>>doc:Battery management systems.BMS Main 3.5\. Firmware update.WebHome]].
4 +)))
3 3  
6 += v2.2.3 =
7 +
8 +[[BMS_Main_3_v2.2.3.bin>>FileManager.BMS_Main_3_v2\.2\.3\.bin]]
9 +
10 +== Improvements ==
11 +
12 +* new parameter for setting the type of network to which the BMS GSM communication module connects (see the "Connectivity - Cellular" section)
13 +
14 +== Fixes ==
15 +
16 +* resolving the issue of ill-considered reduction of the battery SOC level when the cell voltage is close to the level corresponding to SOC=0% (due to the flow of a large discharge current leading to the high voltage drop on the cells)
17 +
18 += v2.2.2 =
19 +
20 +[[BMS_Main_3_v2.2.2.bin>>FileManager.BMS_Main_3_v2\.2\.2\.bin]]
21 +
22 +== Improvements ==
23 +
24 +* increasing the accuracy of resistance calculations
25 +* new parameters for battery manufacturers: manufacturer name, hardware ID, software ID, configuration description, production date (see the "Service - User settings" section)
26 +
27 += v2.2.1 =
28 +
29 +[[BMS_Main_3_v2.2.1.bin>>FileManager.BMS_Main_3_v2\.2\.1\.bin]]
30 +
31 +== Improvements ==
32 +
33 +* increasing the smoothness of changing the current limit values
34 +* ability to exclude errors from being saved in the error journal (see the "Service - Errors journal" section)
35 +* extension of the CANopen dictionary to provide additional information for the BMS Display (device serial number, battery serial number, battery address, Wi-Fi and LAN addresses, SOH, capacity, etc.)
36 +
37 +== Fixes ==
38 +
39 +* resolving the issue of working with the Fronius charger over the CAN1 interface
40 +* small internal fixes
41 +
42 += v2.2.0 =
43 +
44 +[[BMS_Main_3_v2.2.0.bin>>FileManager.BMS_Main_3_v2\.2\.0\.bin]]
45 +
46 +== Features ==
47 +
48 +* support for the HYG Global CAN protocol version 2 (June 13, 2024)
49 +* calculation of regenerated energy
50 +* calculation of new lifetime parameters: average temperature, average charge/discharge currents, etc. See the counters in the "Service - Counters" section
51 +* new "Need acknowledge" warning signal that is set when a new record is created in the errors journal. The signal can be cleared in the "Service - Errors journal" section
52 +* new parameter for setting the condition for starting balancing: automatically (regardless of the command) or on the balancing request (see the "Control - Cell balancing" section)
53 +* new option to start balancing if the cell voltage exceeds the "Voltage for forced balancing" value (see the "Control - Cell balancing" section)
54 +* new Max-Min algorithm for calculating the final battery SOC in the "Control - SOC estimation" section
55 +* new flags in the "Protections - Undervoltage" and "Protections - Overvoltage" sections which allow using the calculated open circuit cell voltage instead of the actual voltage to detect the "Undervoltage" and "Overvoltage" errors, respectively
56 +* ability to check the "Ready to charge" and "Ready to discharge" signals to control the charging and discharging contactors (see the "Control - Charge" and "Control - Discharge" sections)
57 +* improved control of the precharging contactor, which can precharge capacitive load using multiple attempts and detect high power dissipated in the precharge resistor (see the "Control - Precharge" section)
58 +* ability to select errors that the device saves in the errors journal (see the "Service - Errors journal" section)
59 +
60 +== Improvements ==
61 +
62 +* ability to configure and monitor the device via the CAN1 (ext) bus
63 +* placing the device input signals to the "Battery" section and adding raw discrete inputs to the "Signals" section
64 +
65 +== Fixes ==
66 +
67 +* using the calculated open circuit voltage to set/clear the "Ready to charge" and "Ready to discharge" signals
68 +
4 4  = v2.1.1 =
5 5  
6 6  [[BMS_Main_3_v2.1.1.bin>>FileManager.BMS_Main_3_v2\.1\.1\.bin]]