Skip to Content

Changes for page BMS Main 2.1

Last modified by Admin on 2025/04/14 10:35
From version 6.1
edited by Admin
on 2024/12/17 12:51
Change comment: There is no comment for this version
To version 11.1
edited by Admin
on 2025/04/02 10:05
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,6 +1,59 @@
1 -(% class="wikigeneratedid" %)
1 +(% class="box infomessage" %)
2 +(((
2 2  BMS Main 2.1 firmware update procedure is described [[here>>doc:Battery management systems.BMS Main 2\.1.4\. Firmware update.WebHome]].
4 +)))
3 3  
6 += v1.70.0 =
7 +
8 +[[BMS_Main_2.1_v1.70.0.srec>>FileManager.BMS_Main_2\.1_v1\.70\.0\.srec]]
9 +
10 +== Features ==
11 +
12 +* new parameters allowing to set different delays for battery discharge mode to detect the overcurrent error (see the "Protections - Overcurrent protection" section)
13 +* new flag that sets whether the BMS should wait for confirmation messages from the Combilift truck to start charging or not (see the "External equipment - Combilift truck" section)
14 +
15 +== Fixes ==
16 +
17 +* optimization of the logging process, minimizing the time to open the next log file if the current one is full
18 +
19 += v1.69.1 =
20 +
21 +[[BMS_Main_2.1_v1.69.1.srec>>FileManager.BMS_Main_2\.1_v1\.69\.1\.srec]]
22 +
23 +== Fixes ==
24 +
25 +* check the HYG and Combilift confirmation flags only if the truck offline error is not set
26 +* small internal fixes
27 +
28 += v1.69.0 =
29 +
30 +[[BMS_Main_2.1_v1.69.0.srec>>FileManager.BMS_Main_2\.1_v1\.69\.0\.srec]]
31 +
32 +== Features ==
33 +
34 +* new parameter for setting the condition for starting balancing: automatically (regardless of the command) or on the balancing request (see the "Cells - Cell balancing" section)
35 +* new option to start balancing if the cell voltage exceeds the "Voltage for forced balancing" value (see the "Cells - Cell balancing" section)
36 +* new assignment "Balancing request" for the discrete inputs (see the "Signals - Input signals" section)
37 +* new Max-Min algorithm for calculating the final battery SOC in the "Cells - SOC estimation" section
38 +* new algorithms "Automatic" and "On command" for the main contactor (see the "Cells - Main contactor" section)
39 +* new assignment "Close Main contactor" for the discrete inputs to close the main contactor by a command
40 +* new assignment "Close External 1" for the discrete inputs (see the "Signals - Input signals" section)
41 +* new assignment "External 1" for the discrete outputs and relays (see the "Signals - Output signals" section). The "External 1" output is directly controlled by the "Close External 1" command.
42 +* new "Precharge error" flag that is set when precharging cannot be completed
43 +* new flags in the "Protections - Undervoltage protection" and "Protections - Overvoltage protection" sections which allow using the calculated open circuit cell voltage instead of the actual voltage to detect the "Undervoltage" and "Overvoltage" errors, respectively
44 +* ability to check the "Ready to charge" and "Ready to discharge" signals to control the charging and discharging contactors (see the "Cells - Charging control" and "Cells - Discharging control" sections)
45 +
46 +== Improvements ==
47 +
48 +* ignoring the "Need acknowledge" flag when generating Modbus input register 0x2128 ("Error")
49 +* explicit flags to enable the use of the charging current limit for fast and/or normal charging when using the CCS Fast charge controller (see the "External equipment - CCS Fast charge controller" section)
50 +* improving resistance calculation
51 +
52 +== Fixes ==
53 +
54 +* resolving the issue where the "Need acknowledge" signal is not set if any of the device errors are not acknowledged in the error journal
55 +* using the calculated open circuit voltage to set/clear the "Ready to charge" and "Ready to discharge" signals
56 +
4 4  = v1.68.0 =
5 5  
6 6  [[BMS_Main_2.1_v1.68.0.srec>>FileManager.BMS_Main_2\.1_v1\.68\.0\.srec]]