Skip to Content

Changes for page BMS Main 2.1

Last modified by Admin on 2025/04/14 10:35
From version 3.1
edited by Admin
on 2024/11/22 09:07
Change comment: There is no comment for this version
To version 8.1
edited by Admin
on 2025/01/21 08:01
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,3 +1,45 @@
1 +(% class="box infomessage" %)
2 +(((
3 +BMS Main 2.1 firmware update procedure is described [[here>>doc:Battery management systems.BMS Main 2\.1.4\. Firmware update.WebHome]].
4 +)))
5 +
6 += v1.69.0 =
7 +
8 +[[BMS_Main_2.1_v1.69.0.srec>>FileManager.BMS_Main_2\.1_v1\.69\.0\.srec]]
9 +
10 +== Features ==
11 +
12 +* new parameter for setting the condition for starting balancing: automatically (regardless of the command) or on the balancing request (see the "Cells - Cell balancing" section)
13 +* new option to start balancing if the cell voltage exceeds the "Voltage for forced balancing" value (see the "Cells - Cell balancing" section)
14 +* new assignment "Balancing request" for the discrete inputs (see the "Signals - Input signals" section)
15 +* new Max-Min algorithm for calculating the final battery SOC in the "Cells - SOC estimation" section
16 +* new algorithms "Automatic" and "On command" for the main contactor (see the "Cells - Main contactor" section)
17 +* new assignment "Close Main contactor" for the discrete inputs to close the main contactor by a command
18 +* new assignment "Close External 1" for the discrete inputs (see the "Signals - Input signals" section)
19 +* new assignment "External 1" for the discrete outputs and relays (see the "Signals - Output signals" section). The "External 1" output is directly controlled by the "Close External 1" command.
20 +* new "Precharge error" flag that is set when precharging cannot be completed
21 +* new flags in the "Protections - Undervoltage protection" and "Protections - Overvoltage protection" sections which allow using the calculated open circuit cell voltage instead of the actual voltage to detect the "Undervoltage" and "Overvoltage" errors, respectively
22 +* ability to check the "Ready to charge" and "Ready to discharge" signals to control the charging and discharging contactors (see the "Cells - Charging control" and "Cells - Discharging control" sections)
23 +
24 +== Improvements ==
25 +
26 +* ignoring the "Need acknowledge" flag when generating Modbus input register 0x2128 ("Error")
27 +* explicit flags to enable the use of the charging current limit for fast and/or normal charging when using the CCS Fast charge controller (see the "External equipment - CCS Fast charge controller" section)
28 +* improving resistance calculation
29 +
30 +== Fixes ==
31 +
32 +* resolving the issue where the "Need acknowledge" signal is not set if any of the device errors are not acknowledged in the error journal
33 +* using the calculated open circuit voltage to set/clear the "Ready to charge" and "Ready to discharge" signals
34 +
35 += v1.68.0 =
36 +
37 +[[BMS_Main_2.1_v1.68.0.srec>>FileManager.BMS_Main_2\.1_v1\.68\.0\.srec]]
38 +
39 +== Features ==
40 +
41 +- support for charge/discharge cycling using XD Discharger (see the sections "External equipment - Battery cycling" and "External equipment - XD Discharger (cycling)")
42 +
1 1  = v1.67.0 =
2 2  
3 3  [[BMS_Main_2.1_v1.67.0.srec>>FileManager.BMS_Main_2\.1_v1\.67\.0\.srec]]