Skip to Content

Changes for page BMS Repeater

Last modified by Admin on 2025/05/28 18:26
From version 1.2
edited by Admin
on 2024/12/13 16:00
Change comment: Update document after refactoring.
To version 10.1
edited by Admin
on 2025/05/28 18:26
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,9 +1,9 @@
1 -= General information =
1 += General information =
2 2  
3 3  
4 4  [[image:1734105245109-437.png||data-xwiki-image-style-alignment="center" height="137" width="300"]]
5 5  
6 -The BMS Repeater 1.x is a device for relaying RS-485 signals from one subnetwork to another and vice versa.
6 +The BMS Repeater is a device for relaying RS-485 signals from one subnetwork to another and vice versa.
7 7  
8 8  The device provides galvanic isolation up to 3500 V RMS.
9 9  
... ... @@ -10,21 +10,27 @@
10 10  = Specifications =
11 11  
12 12  |**Parameter**|**Value**
13 -|Supply voltage, V|5.0±0.5
13 +|Supply voltage, V|5.0 ± 0.5
14 14  |Current consumption @5 V, mA (no load; max)|40
15 15  |RS-485 baud rate, bps (max)|115200
16 -|Output voltage, V|5.0±0.5
16 +|Output voltage, V|5.0 ± 0.5
17 17  |Output current, mA (max)|400
18 18  |Dimensions (length × width × height), mm|64 × 30 × 16
19 -|Weight, g|13±2
19 +|Weight, g|13 ± 5
20 20  |(% colspan="2" %)**Operating conditions**
21 -|Operating temperature range, ° С|-40÷75
21 +|Operating temperature range, ° С|-40 to +85
22 22  |Degree of protection from external influences|IP00
23 +|Header types|Molex series Mini-Fit
23 23  
24 24  = Connection =
25 25  
26 -The BMS Repeater 1.x has a header to connect the BMS Main (X1) and a header to connect BMS Logic (X2). It also has jumpers to connect bias resistors to the RS-485 bus subnetworks.
27 +(% class="box errormessage" %)
28 +(((
29 +The BMS can be connected to batteries with life-threatening and health-hazardous voltage levels. When working with high-voltage batteries, observe electrical safety regulations, use safety glasses, protective clothing, insulated tools and appliances. To prevent the damage of device avoid electrostatic discharges while working with the battery.
30 +)))
27 27  
32 +The BMS Repeater a header to connect the any BMS Main board and a header to connect any BMS Logic board. It also has jumpers to connect bias resistors to the RS-485 bus subnetworks.
33 +
28 28  [[image:1734105319233-615.png||data-xwiki-image-style-alignment="center" height="353" width="350"]]
29 29  
30 30  |**Parameter**|**Value**
... ... @@ -31,10 +31,11 @@
31 31  |Overall dimensions (length × width × height), mm|64 × 30 × 16
32 32  |Mounting dimensions (length × width), mm|57 × 23
33 33  |Mounting holes|M3
34 -|Header types|Molex series Mini-Fit
35 35  
36 -== X1 – header for communication with BMS Main ==
41 +== X1 – header for communication with BMS Main board ==
37 37  
43 +Receptacle Housing: Molex 39012040. Terminals: Molex 5556
44 +
38 38  [[image:1734105400608-295.png||data-xwiki-image-style-alignment="center" height="83" width="75"]]
39 39  
40 40  |**Pin**|**Name**|**Description**
... ... @@ -43,8 +43,10 @@
43 43  |**3**|**+5V**|Supply voltage 5V
44 44  |**4**|**GND1**|Ground
45 45  
46 -== X2 – header for communication with BMS Logic ==
53 +== X2 – header for communication with BMS Logic board ==
47 47  
55 +Receptacle Housing: Molex 39012040. Terminals: Molex 5556
56 +
48 48  [[image:1734105400608-295.png||data-xwiki-image-style-alignment="center" height="83" width="75"]]
49 49  
50 50  |**Pin**|**Name**|**Description**