Skip to Content
Last modified by Admin on 2025/03/18 12:50
From version 5.1
edited by Admin
on 2024/12/09 16:58
Change comment: There is no comment for this version
To version 6.1
edited by Admin
on 2024/12/23 16:02
Change comment: There is no comment for this version

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -drafts.BMS Mini 2.WebHome
1 +Battery management systems.BMS Mini 2.WebHome
Content
... ... @@ -3,13 +3,13 @@
3 3  
4 4  == Installation procedure ==
5 5  
6 -The mounting area of the BMS Mini 2 must be protected from mechanical particles (dust, dirt, large objects) and water. The BMS Mini 2 is recommended to be placed close to the cells it controls, but away from high current circuits to reduce interference to measuring circuits and increase overall reliability of installation.
6 +The mounting area of the BMS Mini must be protected from mechanical particles (dust, dirt, large objects) and water. The BMS Mini is recommended to be placed close to the cells it controls, but away from high current circuits to reduce interference to measuring circuits and increase overall reliability of installation.
7 7  
8 8  The installation site must provide convenient access for subsequent connection to the device’s headers for connecting other system elements: a current sensor, contactors, display panels.
9 9  
10 -The BMS Mini 2 has a heat sink to dissipate the heat generated during the balancing of the cells. When used in enclosed enclosures, heat must be removed from the sink, otherwise it may damage the device.
10 +The BMS Mini has a heat sink to dissipate the heat generated during the balancing of the cells. When used in enclosed enclosures, heat must be removed from the sink, otherwise it may damage the device.
11 11  
12 -Overall and mounting dimensions of the BMS Mini 2 are shown on figures below.
12 +Overall and mounting dimensions of the BMS Mini are shown on figures below.
13 13  
14 14  [[image:1733738313780-948.png||data-xwiki-image-style-alignment="center" height="442" width="547"]]
15 15  
... ... @@ -26,7 +26,7 @@
26 26  
27 27  == Headers ==
28 28  
29 -There are names and locations of the BMS Mini 2 headers on figure below.
29 +There are names and locations of the BMS Mini headers on figure below.
30 30  
31 31  [[image:1733738660900-622.png||data-xwiki-image-style-alignment="center" height="379" width="508"]]
32 32  
... ... @@ -162,11 +162,11 @@
162 162  
163 163  |**Pin**|**Name**|**Description**
164 164  |**1**|**VBAT+**|Supply voltage for BMS Mini
165 -|**2**|**VBAT-**|BMS Mini 2 power ground
165 +|**2**|**VBAT-**|BMS Mini power ground
166 166  
167 167  (% class="box warningmessage" %)
168 168  (((
169 -**Attention! **The BMS Mini 2 device is **galvanically connected** to the battery (the minus of the battery is the device ground). In view of this, when a BMS Wi-Fi or BMS GSM module is connected to the device, the antenna braid will also be galvanically connected to the battery (connected to the battery negative). It is recommended to** isolate the antenna cable from the battery case **to prevent negative potential from appearing on the case.
169 +**Attention! **The BMS Mini device is **galvanically connected** to the battery (the minus of the battery is the device ground). In view of this, when a BMS Wi-Fi or BMS GSM module is connected to the device, the antenna braid will also be galvanically connected to the battery (connected to the battery negative). It is recommended to** isolate the antenna cable from the battery case **to prevent negative potential from appearing on the case.
170 170  )))
171 171  
172 172  === J1 – jumper for switching CAN bus terminal resistor ===