Skip to Content
Last modified by Admin on 2025/03/18 12:50
From version 1.1
edited by Admin
on 2024/12/09 10:17
Change comment: There is no comment for this version
To version 2.1
edited by Admin
on 2024/12/09 10:17
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -15,10 +15,10 @@
15 15  
16 16  [[image:1733738313786-252.png||data-xwiki-image-style-alignment="center" height="150" width="545"]]
17 17  
18 -| (((
18 +|(((
19 19  **Parameter**
20 20  )))|**Value **
21 -| (((
21 +|(((
22 22  Overall dimensions (length × width × height), mm
23 23  )))|139.5 × 117 × 17
24 24  |Mounting dimensions (length × width), mm|130 × 111
... ... @@ -172,18 +172,18 @@
172 172  
173 173  (% class="box warningmessage" %)
174 174  (((
175 -**Attention! **The BMS Mini S device is **galvanically connected** to the battery (the minus of the battery is the device ground). In view of this, when a BMS Wi-Fi or BMS GSM module is connected to the device, the antenna braid will also be galvanically connected to the battery (connected to the battery negative). It is recommended to** isolate the antenna cable from the battery case **to prevent negative potential from appearing on the case.
175 +**Attention! **The BMS Mini S device is **galvanically connected** to the battery (the minus of the battery is the device ground). In view of this, when a BMS Wi-Fi or BMS GSM module is connected to the device, the antenna braid will also be galvanically connected to the battery (connected to the battery negative). It is recommended to** isolate the antenna cable from the battery case **to prevent negative potential from appearing on the case.
176 176  )))
177 177  
178 178  === J1 – jumper for switching CAN bus terminal resistor ===
179 179  
180 -To connect the terminal resistor between the** CAN_H** and **CAN_L** lines, install the jumper J1 according to the following figure:
180 +To connect the terminal resistor between the** CAN_H** and **CAN_L** lines, install the jumper J1 according to the following figure:
181 181  
182 182  [[image:1733738660910-372.png||data-xwiki-image-style-alignment="center" height="85" width="162"]]
183 183  
184 184  === J2 – jumper for switching RS-485 terminal resistor ===
185 185  
186 -To connect the terminal resistor between the** RS485_A** and **RS485_B** lines, install the jumper J1 according to the following figure:
186 +To connect the terminal resistor between the** RS485_A** and **RS485_B** lines, install the jumper J1 according to the following figure:
187 187  
188 188  [[image:1733738660910-372.png||data-xwiki-image-style-alignment="center" height="85" width="162"]]
189 189  
... ... @@ -196,7 +196,7 @@
196 196  
197 197  Begin the connection with the negative line of the battery: the “C0“ is connected to the “B-“, then the first cell (C1) is connected, then the second (С2), etc. If not all inputs of the cells are used, then the remaining inputs are connected to the cell with the most potential.
198 198  
199 -[[image:1733738660912-678.png||data-xwiki-image-style-alignment="center" height="474" width="945"]]
199 +[[image:1733738660912-678.png||data-xwiki-image-style-alignment="center" height="326" width="650"]]
200 200  
201 201  (% class="box warningmessage" %)
202 202  (((