Changes for page 3.5 External equipment

Last modified by Admin on 2025/02/26 17:09

From 2.1 to 2.2

From version 2.2

edited by Admin
on 2025/02/26 14:32

Change comment: There is no comment for this version

To version 10.1

edited by Admin
on 2025/02/26 17:09

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)
Attachments (0 modified, 5 added, 0 removed)

Details

Page properties

Content

@@ -232,7 +232,7 @@
  After changing the settings, restart the BMS Mini device.
  )))
--=== Sunny Island inverter ===
++=== SMA Sunny Island inverter ===
  To change the communication parameters with an SMA Sunny Island inverter, select the "External equipment → inverters → SMA Sunny Island inverter" section:
@@ -251,6 +251,41 @@
  When working with the Sunny Island inverter, the BMS Mini device sends messages with the values of voltage and charge/discharge current continuously with the period “Output period”: Charging voltage, Charging current, Discharging voltage, Discharging current.
++=== Pylontech inverter ===
++
++To change the parameters of communication with a Pylontech inverter, select the "External equipment → Inverters and loads → Pylontech inverter" section:
++
++[[image:1740580440283-115.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="126" width="800"]]
++
++In this section:
++
++* Enable – a flag to enable communication with the inverter;
++* Type – invertor type:
++** Pylontech;
++** Solis;
++* Charge voltage, V – maximum charging voltage, V;
++* Charge current, А – maximum charging current, A;
++* Discharge voltage (min) – minimum discharging voltage, V;
++* Discharge current – maximum discharging current, А.
++
++=== ASTOM load bank (cycling) ===
++
++To change the parameters of communication with a ASTOM load bank, select the "External equipment → Inverters and loads → ASTOM load bank (cycling)" section:
++
++[[image:1740580507794-408.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="190" width="800"]]In this section:
++
++* Enable – a flag to enable communication with the bank;
++* Number of discharge cycles;
++* Minimum voltage of charged cells, V;
++* Voltage deviation of charged cells – minimum allowable deviation of the cells voltage at which battery states as charged, V;
++* Maximum discharge current, A;
++* Cell voltage to stop discharging, V;
++* SOC to be at the end of cycling – target SOC at the end of charge-discharge cycling, V;
++* Delay before starting discharging – a delay before transmitting command to the load to start discharging, millisecond;
++* Check the difference between the min and max cell voltage – a flag to enable check of difference between the minimum and maximum cell voltages to generate an error;
++* Voltage difference – difference between the minimum and maximum cell voltages for error to be generated and cycling to be stopped, V;
++* Delay before setting the error – a delay before generating an error, second.
++
  === HYG Class I-III truck ===
  The HYG Class I-III equipment is installed on the forklifts by the group of companies HYSTER-YALE.
@@ -298,7 +298,7 @@
  To change communication parameters with a Combilift forklift, select the "External equipment → Trucks and Vehicles → Combilift truck" section:
--[[image:1733753328056-822.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="158" width="800"]]
++[[image:1740580581620-608.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="169" width="800"]]
  In this section:
@@ -308,6 +308,7 @@
  * Receive timeout – a timeout for receiving packets from the forklift (if no data is being received from the forklift during this time, the “Combilift offline“ flag is set), millisecond; at a value of 0 milliseconds, the "Combilift offline" error does not occur;
  * Inhibit charging on the "Combilift offline" error – a flag to forbid charging if the "Combilift offline" error is generated;
  * Inhibit discharging on "Combilift offline" error – a flag to forbid discharging if the "Combilift offline" error is generated;
++* Do not set the "Combilift offline" error on the "Charger connected" signal;
  * SOC: Limited operation – a SOC level, at which the forklift goes into a state of limited functionality, %;
  * SOC: Lift lockout – a SOC level, at which the forklift locks the lift, %;
  * Send Heartbeat messages – a flag to enable generation of the Heartbeat messages to forklift;
@@ -415,13 +415,6 @@
  After changing the settings, restart the BMS Mini device.
  )))
--===   ===
--
--(% class="box infomessage" %)
--(((
--
--)))
--
  === ZiK truck ===
  To change communication parameters with a ZiK truck, select the "External equipment → Trucks and Vehicles → ZiK truck" section:
@@ -430,11 +430,10 @@
  In this section:
--* Settings:
--** Enable – a flag to enable communication with the ZiK truck;
--** Node ID – a ZiK identifier in the CANopen network;
--** SOC: Limited operation – a SOC level at which the truck goes to limited operation mode, %;
--** Send supercapacitor parameters – a flag to enable transmitting the supercapacitor parameters.
++* Enable – a flag to enable communication with the ZiK truck;
++* Node ID – a ZiK identifier in the CANopen network;
++* SOC: Limited operation – a SOC level at which the truck goes to limited operation mode, %;
++* Send supercapacitor parameters – a flag to enable transmitting the supercapacitor parameters.
  The BMS with the identifier “Node ID” continuously transmits to the truck the control commands with a period of 100 milliseconds.
@@ -458,6 +458,34 @@
  * Receive vehicle messages – a flag to activate receiving vehicle messages;
  * First vehicle message ID – an identifier of the first message of the vehicle in the J1939 network.
++=== Bender iso165C ===
++
++To change communication parameters with a Bender iso165C, select the "External equipment → IMD → Bender iso165C" section:
++
++[[image:1740580850472-138.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="125" width="800"]]
++
++In this section:
++
++* Enable – a flag to enable communication with the IMD;
++* Receive timeout – a timeout for receiving packets from the IMD, millisecond;
++* Configure the IMD thresholds – a flag to enable the threshold values for generating insulation error and insulation warning;
++* Threshold to detect insulation error – threshold resistance value to generate the insulation error, Ohm;
++* Threshold to detect insulation warning – threshold resistance value to generate the insulation warning, Ohm.
++
++=== BMS IMD ===
++
++To change communication parameters with a BMS IMD, select the "External equipment → IMD → BMD IMD " section:
++
++[[image:1740580889560-625.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="123" width="800"]]
++
++In this section:
++
++* Enable – a flag to enable communication with the IMD;
++* Node ID – a CANopen address of the BMS IMD device;
++* Configure the IMD thresholds – a flag to override the IMD warning and alarm settings;
++* Threshold to detect insulation alarm, Ohm;
++* Threshold to detect insulation warning, Ohm.
++
  === Main X ===
  The BMS Mini device can connect to BMS Main X strings controller.

1740580440283-115.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+22.6 KB

Content

1740580507794-408.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+32.4 KB

Content

1740580581620-608.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+30.2 KB

Content

1740580850472-138.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+18.3 KB

Content

1740580889560-625.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+17.2 KB

Content

Changes for page 3.5 External equipment

Summary

Details

Applications

Navigation

Table of Contents