Skip to Content

Changes for page 3.4 Protections

Last modified by Admin on 2026/04/27 13:04
From version 28.2
edited by Admin
on 2026/04/27 13:02
Change comment: There is no comment for this version
To version 1.2
edited by Admin
on 2024/12/09 16:56
Change comment: Update document after refactoring.

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -Battery management systems.BMS Mini S.3\. Configuration.WebHome
1 +drafts.BMS Mini S BMS Mini 2.3\. Configuration.WebHome
Content
... ... @@ -6,12 +6,6 @@
6 6  
7 7  The BMS Mini device continuously monitors the state of the cells, the external environment and, when detecting abnormalities, protects the battery and system components from damage.
8 8  
9 -(% class="box errormessage" %)
10 -(((
11 -**Attention!**
12 -Behavior of contactors at different errors is configured in **corresponding contactor settings**!
13 -)))
14 -
15 15  === Overcurrent ===
16 16  
17 17  The BMS Mini device performs the overcurrent protection depending on current sensor values.
... ... @@ -43,46 +43,11 @@
43 43  * the current is positive (charging) or zero, and its modulo value is less than the “Tolerant charging current” value for the “Delay before clearing the error” time;
44 44  * the current is negative (discharging), and its modulo value is less than the “Tolerant discharging current” value for the “Delay before clearing the error” time.
45 45  
46 -=== Charge current limit ===
40 +(% class="box infomessage" %)
41 +(((
42 +If there is the "Overcurrent" error, the **charging **and **discharging **contactors open.
43 +)))
47 47  
48 -The BMS Mini device can check if the charging current exceeds the estimated limit based on the [[Charge map>>doc:Battery management systems.BMS Mini S.3\. Configuration.3\.3 Control.WebHome||anchor="HChargemap"]]. If current exceeds the calculated limit more than configured difference, "Current limit" error is generated.
49 -
50 -Current difference is separated to two regions by the threshold value. Maximum current in Region 1 is calculated by the absolute difference, in Region 2 – by the relative difference.
51 -
52 -To change the overcurrent protection of the battery, select the "Protections → Charge current limit" section:
53 -
54 -[[image:1740571132019-848.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="143" width="800"]]
55 -
56 -In this section:
57 -
58 -* Enable – a flag to enable the protection;
59 -* Threshold to switch from Region 1 to Region 2 – a current value at which current excess calculation will be switched from absolute to relative difference, A;
60 -* Region 1: Current difference – a value of maximum absolute current difference, A;
61 -* Region 2: Current difference – a value of maximum relative current excess, A;
62 -* Delay before setting the error, millisecond;
63 -* Delay before clearing the error, second;
64 -* Lock – a flag to block the error until the device is restarted.
65 -
66 -=== Discharge current limit ===
67 -
68 -The BMS Mini device can check if the discharging current exceeds the estimated limit based on the [[Discharge map>>doc:Battery management systems.BMS Mini S.3\. Configuration.3\.3 Control.WebHome||anchor="HDischargemap"]]. If current exceeds the calculated limit more than configured difference, "Current limit" error is generated.
69 -
70 -Current difference is separated to two regions by the threshold value. Maximum current in Region 1 is calculated by the absolute difference, in Region 2 – by the relative difference.
71 -
72 -To change the overcurrent protection of the battery, select the "Protections → Discharge current limit" section:
73 -
74 -[[image:1740571296344-411.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="151" width="800"]]
75 -
76 -In this section:
77 -
78 -* Enable – a flag to enable the protection;
79 -* Threshold to switch from Region 1 to Region 2 – a current value at which current excess calculation will be switched from absolute to relative difference, A;
80 -* Region 1: Current difference – a value of maximum absolute current difference, A;
81 -* Region 2: Current difference – a value of maximum relative current excess, A;
82 -* Delay before setting the error, millisecond;
83 -* Delay before clearing the error, second;
84 -* Lock – a flag to block the error until the device is restarted.
85 -
86 86  === Undervoltage ===
87 87  
88 88  The BMS Mini device implements battery protection from too low voltage on the cells.
... ... @@ -89,7 +89,7 @@
89 89  
90 90  To change the battery protection parameters from low voltage on the cells, select the "Protections → Undervoltage" section:
91 91  
92 -[[image:1740571345293-460.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="138" width="800"]]
51 +[[image:1733748033237-837.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="127" width="800"]]
93 93  
94 94  In this section:
95 95  
... ... @@ -96,7 +96,6 @@
96 96  * Enable – a flag to enable the protection;
97 97  * Minimum cell voltage, V;
98 98  * Tolerant cell voltage, V;
99 -* Check the open circuit voltage instead of the actual voltage – a flag to use the U,,ocv,, (corrected due to current and cell resistance) cell voltage instead of measured value;
100 100  * Delay before setting the error, millisecond;
101 101  * Delay before clearing the error, second;
102 102  * Lock – a flag to block the error until the device is restarted.
... ... @@ -111,6 +111,11 @@
111 111  
112 112  * the minimum voltage among all cells of the battery is greater than the “Tolerant cell voltage” value for the “Delay before clearing the error” time.
113 113  
72 +(% class="box infomessage" %)
73 +(((
74 +If there is the "Undervoltage" error, the **discharging **contactor opens.
75 +)))
76 +
114 114  === Overvoltage ===
115 115  
116 116  The BMS Mini device implements battery protection from too high voltage on the cells.
... ... @@ -117,7 +117,7 @@
117 117  
118 118  To change the battery protection parameters from high voltage on the cells, select the "Protections → Overvoltage" section:
119 119  
120 -[[image:1740571383842-536.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="147" width="800"]]
83 +[[image:1733748033238-995.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="138" width="800"]]
121 121  
122 122  In this section:
123 123  
... ... @@ -124,9 +124,9 @@
124 124  * Enable – a flag to enable the protection;
125 125  * Maximum cell voltage, V;
126 126  * Tolerant cell voltage, V;
127 -* Check the open circuit voltage instead of the actual voltage – a flag to use the U,,ocv,, (corrected due to current and cell resistance) cell voltage instead of measured value;
128 128  * Delay before setting the error, millisecond;
129 129  * Delay before clearing the error, second;
92 +* Switch off the discharging contactor on error – a flag to open the discharging contactor when the "Overvoltage" error is generated;
130 130  * Lock – a flag to block the error until the device is restarted.
131 131  
132 132  As a result of the operation of the battery protection from high voltage, the "Overvoltage" error is generated.
... ... @@ -139,33 +139,11 @@
139 139  
140 140  * the maximum voltage among all cells of the battery is less than the “Tolerant cell voltage” value for the “Delay before clearing the error” time.
141 141  
142 -=== Cell imbalance ===
105 +(% class="box infomessage" %)
106 +(((
107 +If there is the "Overvoltage" error, the **charging **contactor and **discharging **contactor open (if the “Switch off the discharging contactor on error” flag is set).
108 +)))
143 143  
144 -The BMS Mini S device implements battery protection from too much cell imbalance. If balancing algorithm is not enough to compensate battery imbalance, then imbalance protection generates an error when imbalance is above estimated threshold.
145 -
146 -To change the battery protection parameters from cell imbalance, select the "Protections → Cell imbalance" section:
147 -
148 -[[image:1762772978976-565.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="145" width="800"]]
149 -
150 -In this section:
151 -
152 -* Enable – a flag to enable the protection;
153 -* Maximum cell imbalance, V;
154 -* Tolerant cell imbalance, V;
155 -* Delay before setting the error, millisecond;
156 -* Delay before clearing the error, second;
157 -* Lock – a flag to block the error until the device is restarted.
158 -
159 -As a result of the operation of the battery protection from cell imbalance, the "Cell imbalance” error is generated.
160 -
161 -Error generation conditions:
162 -
163 -* the voltage difference between the most charged cell and the least charged cell is more than the “Maximum cell imbalance” value for the “Delay before setting the error” time.
164 -
165 -Conditions for removing the error:
166 -
167 -* the voltage difference between the most charged cell and the least charged cell is less than the “Tolerant cell imbalance” value for the “Delay before clearing the error” time.
168 -
169 169  === Low temperature ===
170 170  
171 171  The BMS Mini device implements battery protection from too low temperature.
... ... @@ -195,6 +195,11 @@
195 195  
196 196  * the minimum temperature among all cells of the battery is greater than the “Tolerant charging (discharging) temperature” value for the “Delay before clearing the error” time.
197 197  
139 +(% class="box infomessage" %)
140 +(((
141 +If there is the "Low temperature (CH)" error, the **charging **contactor opens. If there is the "Low temperature (DCH)" error, the **discharging **contactor opens.
142 +)))
143 +
198 198  === High temperature ===
199 199  
200 200  The BMS Mini device implements battery protection from too high temperature.
... ... @@ -224,6 +224,11 @@
224 224  
225 225  * the maximum temperature among all cells of the battery is less than the “Tolerant charging (discharging) temperature” value for the “Delay before clearing the error” time.
226 226  
173 +(% class="box infomessage" %)
174 +(((
175 +If there is the "High temperature (CH)" error, the **charging **contactor opens. If there is the "High temperature (DCH)" error, the **discharging **contactor opens.
176 +)))
177 +
227 227  === Battery cover ===
228 228  
229 229  To change the protection parameters from opening the battery cover, select the "Protections → Battery cover" section:
... ... @@ -249,15 +249,9 @@
249 249  
250 250  (% class="box warningmessage" %)
251 251  (((
252 -If there is the "Battery cover error", the **“Critical error” **is generated.
203 +If there is the "Battery cover error", the **“Critical error” **is generated **and all contactors open.**
253 253  )))
254 254  
255 -=== High board temperature ===
256 -
257 -BMS Mini monitors its temperature and disables the cell balancing when it overheats.
258 -
259 -To change the overheating protection parameters of BMS Logic devices, select the "Protections → High Logic temperature" section:
260 -
261 261  === Cell monitor offline ===
262 262  
263 263  The BMS Mini device checks if there is connection with cell monitor and set an error if not.
... ... @@ -283,7 +283,7 @@
283 283  
284 284  (% class="box warningmessage" %)
285 285  (((
286 -If there is the " Cell monitor offline error", the **“Critical error” **is generated.
231 +If there is the " Cell monitor offline error", the **“Critical error” **is generated and** all contactors open.**
287 287  )))
288 288  
289 289  === Cell count ===
... ... @@ -312,38 +312,9 @@
312 312  
313 313  (% class="box warningmessage" %)
314 314  (((
315 -If there is the "Cell count error", the **“Critical error” **is generated.
260 +If there is the "Cell count error", the **“Critical error” **is generated and **all contactors open.**
316 316  )))
317 317  
318 -=== Temperature sensor count ===
319 -
320 -To change the protection parameters from the mismatch of the number of temperature sensors to the set value, select the "Protections → Temperature sensor count" section:
321 -
322 -[[image:1762773073782-768.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="130" width="800"]]
323 -
324 -In this section:
325 -
326 -* Enable – a flag to enable the protection;
327 -* Number of cells – a number of temperature sensors connected to the BMS;
328 -* Delay before setting the error, millisecond;
329 -* Delay before clearing the error, second;
330 -* Lock – a flag to block the error until the device is restarted.
331 -
332 -As a result of the operation of the protection from the mismatch of the number of cells, the "T-sensor count error" is generated.
333 -
334 -Error generation conditions:
335 -
336 -* the number of temperature sensors connected to the BMS is **not equal** to the “Number of temperature sensors” value during the “Delay before setting the error” time.
337 -
338 -Conditions for removing the error:
339 -
340 -* the number of temperature sensors connected to the BMS is **equal** to the “Number of temperature sensors” value during the “Delay before clearing the error” time.
341 -
342 -(% class="box warningmessage" %)
343 -(((
344 -If there is the "T-sensor count error", the **“Critical error” **is generated**.**
345 -)))
346 -
347 347  === Short circuit ===
348 348  
349 349  The BMS Mini device implements a protection of power circuits (contactors, power wires) against overheating caused by the flow of high current for a long time.
... ... @@ -373,6 +373,11 @@
373 373  
374 374  * the current modulo is lower than the “Maximum current” values for all three protection levels during the “Delay before setting the error” time.
375 375  
292 +(% class="box infomessage" %)
293 +(((
294 +If there is the "Short circuit" error, the **charging **contactor opens (the “Switch off the charging contactor on error” flag is set) and the **discharging **contactor opens (the “Switch off the discharging contactor on error flag” is set).
295 +)))
296 +
376 376  === High contactor temperature ===
377 377  
378 378  The BMS Mini device protects power contactors from overheating. To measure the temperature of the contactor, one of the thermistors connected to the X6 connector is used.
... ... @@ -436,27 +436,9 @@
436 436  
437 437  (% class="box warningmessage" %)
438 438  (((
439 -If there is the “Current sensor error”, the **“Critical error” **is generated.
360 +If there is the “Current sensor error”, the **“Critical error” **is generated and** all contactors open.**
440 440  )))
441 441  
442 -=== MOSFET ===
443 -
444 -BMS Mini S device checks the status of MOSFET switches that are used to control the contactors. To change the parameters of the MOSFET switch protection, select the "Protections → MOSFET " section:
445 -
446 -[[image:1762773566548-852.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="105" width="800"]]
447 -
448 -In this section:
449 -
450 -* Delay before clearing the error, second;
451 -* Lock – a flag to block the error until the device is restarted.
452 -
453 -The “MOSFET error” occurs when the device detects a shortage in contactor coil control circuit or an overheating of the MOSFET switch. Error is removed when the temperature of MOSFET switch is normal during “Delay before clearing the error” time.
454 -
455 -(% class="box warningmessage" %)
456 -(((
457 -If there is the "MOSFET error", the **“Critical error” **is generated.
458 -)))
459 -
460 460  === Charge contactor cycles ===
461 461  
462 462  The BMS Mini device protects the charging contactor against frequent switching.
... ... @@ -473,6 +473,7 @@
473 473  * Delay before setting the error, millisecond;
474 474  * Delay before clearing the error, second;
475 475  * Lock – a flag to block the error until the device is restarted.
379 +* Number of cycles – a number of the charging contactor switchings made during battery operation.
476 476  
477 477  If there is the high switching frequency of the charging contactor, the “CH contactor cycles error” is generated.
478 478  
... ... @@ -484,13 +484,18 @@
484 484  
485 485  * the “Delay before clearing the error” time has passed since the error was generated.
486 486  
487 -=== Discharge contactor cycles ===
391 +(% class="box infomessage" %)
392 +(((
393 +If there is the "CH contactor cycles error" error, the **charging** contactor opens.
394 +)))
488 488  
396 +=== Discharge contactor cycles protection ===
397 +
489 489  The BMS Mini device protects the discharging contactor against frequent switching.
490 490  
491 491  To change the protection parameters against high frequency switching of the discharging contactor, select the "Protections → Discharging contactor cycles" section:
492 492  
493 -[[image:1740571600741-802.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="128" width="800"]]
402 +[[image:1733748068420-615.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="139" width="800"]]
494 494  
495 495  In this section:
496 496  
... ... @@ -500,6 +500,7 @@
500 500  * Delay before setting the error, millisecond;
501 501  * Delay before clearing the error, second;
502 502  * Lock – a flag to block the error until the device is restarted.
412 +* Number of cycles – a number of the charging contactor switchings made during battery operation.
503 503  
504 504  If there is the high switching frequency of the discharging contactor, the “DCH contactor cycles error” is generated.
505 505  
... ... @@ -511,6 +511,11 @@
511 511  
512 512  * the “Delay before clearing the error” time has passed since the error was generated.
513 513  
424 +(% class="box infomessage" %)
425 +(((
426 +If there is the "DCH contactor cycles error" error, the **discharging **contactor opens.
427 +)))
428 +
514 514  === Temperature sensors ===
515 515  
516 516  The BMS Mini device checks the temperature sensors connection circuits. The circuits are checked for breakage and short-circuit.
... ... @@ -530,7 +530,7 @@
530 530  
531 531  (% class="box warningmessage" %)
532 532  (((
533 -If there is the “No temp. sensors” or “Temp. sensor is shorted” error, the **“Critical error” **is generated.
448 +If there is the “No temp. sensors” or “Temp. sensor is shorted” error, the **“Critical error” **is generated and **all contactors open.**
534 534  )))
535 535  
536 536  === WDT reset ===
... ... @@ -553,7 +553,7 @@
553 553  
554 554  (% class="box warningmessage" %)
555 555  (((
556 -If there is the "WDT reset" error, the **“Critical error” **is generated.
471 +If there is the "WDT reset" error, the **“Critical error” **is generated and **all contactors open.**
557 557  )))
558 558  
559 559  === Unallowable charging ===
... ... @@ -581,6 +581,11 @@
581 581  
582 582  * the battery current is zero during the “Delay before clearing the error” time.
583 583  
499 +(% class="box infomessage" %)
500 +(((
501 +If there is the "Unallowable charging" error, the **discharging **contactor opens.
502 +)))
503 +
584 584  === Stuck contactor ===
585 585  
586 586  The BMS Mini device protects contactors against sticking.
... ... @@ -596,15 +596,10 @@
596 596  * Delay before clearing the error, second;
597 597  * Lock – a flag to block the error until the device is restarted.
598 598  
599 -If there is a stuck contactor, the “Stuck contactor” error is generated. Error generation conditions:
519 +If there is a stuck contactor, the “Stuck contactor” error is generated Error generation conditions:
600 600  
601 601  * charging and discharging contactors are open, but the “Charging current present” or “Discharging current present” signal is set.
602 602  
603 -(% class="box warningmessage" %)
604 -(((
605 -If there is the "Stuck contactor" error, the **“Critical error” **is generated.
606 -)))
607 -
608 608  === Contactor feedback ===
609 609  
610 610  The BMS Mini device can receive feedback signals from contactors and detect discrepancy between the control value and the feedback signal. To enable specific contactor protection, the feedback signal must be connected to corresponding contactor feedback pin on X1 header.
... ... @@ -624,11 +624,6 @@
624 624  
625 625  * a command for charging, precharge, discharging, charging/discharging or main contactor not matches its feedback value.
626 626  
627 -(% class="box warningmessage" %)
628 -(((
629 -If there is the "Contactor feedback" error, the **“Critical error” **is generated.
630 -)))
631 -
632 632  === Insulation ===
633 633  
634 634  The BMS Mini device can detect a signal from an external insulation monitoring device (such as Bender IR155) to monitor the insulation quality.
... ... @@ -635,15 +635,11 @@
635 635  
636 636  To change the insulation monitoring parameters, select the "Protections → Insulation" section:
637 637  
638 -[[image:1740573733492-485.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="119" width="800"]]
548 +[[image:1733748083469-478.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="102" width="800"]]
639 639  
640 640  In this section:
641 641  
642 642  * Enable – a flag to enable the protection;
643 -* Checking algorithm – isolation checking mode:
644 -** Always on – check is always performed;
645 -** On charging – check is performed only if “Charger connected” or “Charge request” is set;
646 -** Except charging - check is performed only if “Charger connected” and “Charge request” are cleared;
647 647  * Delay before setting the error, second;
648 648  * Delay before clearing the error, second;
649 649  * Lock – a flag to block the error until the device is restarted.
... ... @@ -650,16 +650,11 @@
650 650  
651 651  Error is set if corresponding discrete input is set up and it receives logical zero.
652 652  
653 -(% class="box warningmessage" %)
654 -(((
655 -If there is the "Insulation" error, the **“Critical error” **is generated.
656 -)))
657 -
658 658  === Critical error ===
659 659  
660 660  To change the critical error parameters, select the "Protections → Critical error" section:
661 661  
662 -[[image:1762775067035-203.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="143" width="800"]]
563 +[[image:1733748083469-183.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="101" width="800"]]
663 663  
664 664  In this section:
665 665  
... ... @@ -666,32 +666,28 @@
666 666  * Enable – a flag to enable the protection;
667 667  * Delay before setting the error, millisecond;
668 668  * Delay before clearing the error, second;
669 -* Errors 1,2 to ignore when setting the critical error;
670 670  * Lock – a flag to block the error until the device is restarted.
671 671  
672 -The "Critical error" signal is generated if at least one of the critical errors (see [[Errors>>doc:Battery management systems.Additional information.1\. Battery controllers\: signals and errors.WebHome||anchor="HErrors"]]) is generated during the “Delay before setting the error” time.
572 +The critical error flag is generated if at least one of the following errors is generated during the “Delay before setting the error” time:
673 673  
574 +* “Battery cover error”;
575 +* “Cell monitor offline”;
576 +* “Cell count error”;
577 +* “ADC error”;
578 +* “Current sensor error”;
579 +* “Shunt offline”;
580 +* “Shunt error”;
581 +* “No temp. sensors”;
582 +* “Temp. sensor is shorted”;
583 +* “Settings error”;
584 +* “WDT reset”;
585 +* “Stuck contactor”;
586 +* “Contactor feedback error”;
587 +* “Insulation fault”.
588 +
674 674  The “Critical error” is cleared if there are no errors from the list above during the “Delay before clearing the error” time.
675 675  
676 -=== General error ===
677 -
678 -To change the general error parameters, select the "Protections → Critical error" section:
679 -
680 -[[image:1740573914327-561.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="129" width="800"]]
681 -
682 -In this section:
683 -
684 -* Enable – a flag to enable the protection;
685 -* Delay before setting the error, millisecond;
686 -* Delay before clearing the error, second;
687 -* Lock – a flag to block the error until the device is restarted;
688 -* Errors 1, 2 to set the "Critical error" – bitfields to enable check of corresponding errors.
689 -
690 -The “General error” is generated if at least one of the enabled errors is generated during the “Delay before setting the error” time.
691 -
692 -The “General error” is cleared if there are no errors from the enabled errors during the “Delay before clearing the error” time.
693 -
694 694  (% class="box warningmessage" %)
695 695  (((
696 -The state of the “General error” can be assigned to a discrete output or to a power switch.
593 +If there is the “Critical error”, **all contactors open.**
697 697  )))
1740571132019-848.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -22.3 KB
Content
1740571296344-411.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -21.9 KB
Content
1740571345293-460.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -22.3 KB
Content
1740571383842-536.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -24.6 KB
Content
1740571600741-802.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -20.6 KB
Content
1740573733492-485.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -23.4 KB
Content
1740573914327-561.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -19.6 KB
Content
1762772949184-209.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -18.0 KB
Content
1762772978976-565.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -18.0 KB
Content
1762773073782-768.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -16.6 KB
Content
1762773136224-775.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -16.6 KB
Content
1762773285560-458.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -16.1 KB
Content
1762773566548-852.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -16.1 KB
Content
1762775067035-203.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -19.4 KB
Content
1777294625990-675.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -14.8 KB
Content