Changes for page 3.4 Protections

Last modified by Admin on 2025/06/11 15:57

From 8.1 to 8.2 From 11.1 to 12.1

From version 8.2

edited by Admin
on 2025/02/28 15:22

Change comment: There is no comment for this version

To version 11.1

edited by Admin
on 2025/02/28 15:27

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)
Attachments (0 modified, 1 added, 0 removed)
- 1740756362809-292.png

Details

Page properties

Content

@@ -215,7 +215,7 @@
  Protection against current unbalance of battery modules is configured in the section "Protections - Current unbalance":
--[[image:1734356793451-440.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="103" width="800"]]
++[[image:Battery management systems.BMS Main 3X.3\. Configuration.3\.4 Protections.WebHome@1734090244843-403.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="116" width="800"]]
  In this section:
@@ -226,8 +226,10 @@
  * Check all the time (not only in the ‘Balancing’ state) – a flag to enable voltage check not only in “Balancing” state;
  * Lock – a flag to block the error until the device is restarted.
--As a result of the operation of the current unbalance protection the errors “Current unbalance (CH)” and “Current unbalance (DCH)” are generated. Conditions for generating the error:
++As a result of the operation of the current unbalance protection the errors “Current unbalance (CH)” and “Current unbalance (DCH)” are generated.
++Conditions for generating the error:
++
  * the current of the battery module is greater than the "Maximum current" value during the "Delay before setting the error" time.
  Conditions for clearing the error:
@@ -234,7 +234,10 @@
  * the current of the battery module is less than the "Maximum current" value during the "Delay before clearing the error" time.
--If there is the error "Current unbalance (CH)" ("Current unbalance (DCH)"), the charging (discharging) contactor of the battery module opens.
++(% class="box infomessage" %)
++(((
++If there is the “Current unbalance (CH)” or "Current unbalance (DCH)" error, **corresponding battery module opens its charging or discharging contactor**.
++)))
  === Charging current unbalance (in “Charging” state) ===
@@ -252,8 +252,10 @@
  * Delay before clearing the error;
  * Lock – a flag to block the error until the device is restarted.
--As a result of the operation of the protection the “Charging current unbalance” are generated. Conditions for generating the errors:
++As a result of the operation of the protection the “Charging current unbalance” are generated.
++Conditions for generating the errors:
++
  * battery module is not included in the largest group of modules whose charge currents differ from each other by no more than "Delta current" during the "Delay before setting the error" time.
  Conditions for clearing the error:
@@ -260,7 +260,10 @@
  * battery module is included in the largest group of modules with similar charge currents during the “Delay before clearing the error” time.
--If there is the “Charging current unbalance” error, the battery module charging contactor opens.
++(% class="box infomessage" %)
++(((
++If there is the “Charging current unbalance” error, **corresponding battery module opens its charging contactor**.
++)))
  === Discharging current unbalance ===
@@ -278,8 +278,10 @@
  * Delay before clearing the error;
  * Lock – a flag to block the error until the device is restarted.
--As a result of the operation of the protection the “Discharging current unbalance” are generated. Conditions for generating the errors:
++As a result of the operation of the protection the “Discharging current unbalance” are generated.
++Conditions for generating the errors:
++
  * battery module is not included in the largest group of modules whose discharge currents differ from each other by no more than "Delta current" during the "Delay before setting the error" time.
  Conditions for clearing the error:
@@ -286,12 +286,51 @@
  * battery module is included in the largest group of modules with similar discharge currents during the “Delay before clearing the error” time.
--If there is the “Discharging current unbalance” error, the battery module discharging contactor opens.
++(% class="box infomessage" %)
++(((
++If there is the “Discharging current unbalance” error, **corresponding battery module opens its discharging contactor**.
++)))
++=== High contactor temperature ===
++
++The BMS Main X device protects power contactors from overheating. To measure the temperature of the contactor, one of the thermistors connected to the X5 connector is used.
++
++To change the overheating protection parameters of power contactors, select the "Protections → High contactor temperature" section:
++
++[[image:1740756362809-292.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="161" width="800"]]
++
++In this section:
++
++* Enable – a flag to enable the protection;
++* Thermistor – a selection of which cell thermistor will be used as contactor temperature sensor;
++* Maximum contactor temperature, °C;
++* Tolerant contactor temperature, °C;
++* Delay before setting the error, second;
++* Delay before clearing the error, second;
++* Lock – a flag to block the error until the device is restarted.
++
++If there is a contactor overheat, the "High contactor temperature" error is generated.
++
++Error generation conditions:
++
++* the contactor temperature is greater than the “Maximum contactor temperature” value during the “Delay before setting the error” time.
++
++Conditions for removing the error:
++
++* the contactor temperature is lower than the “Tolerant contactor temperature” value during the “Delay before clearing the error” time.
++
++=== WDT reset ===
++
++If the BMS firmware hangs, the watchdog timer resets the device. The BMS can detect that the device was reset and generates the “WDT reset” error.
++
++To change the parameters of the watchdog protection, select the "Protections → WDT reset" section:
++
  === Critical error ===
--Parameters for generating the critical error are configured in the "Protections - Critical error" section:
++Some of the errors are system critical. A separate signal named "Critical error" indicates a BMS fault.
++To change the critical error parameters, select the "Protections → Critical error" section:
++
  [[image:1734356802719-477.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="69" width="600"]]
  In this section:
@@ -301,18 +301,6 @@
  * Delay before clearing the error;
  * Lock – a flag to block the error until the device is restarted.
--The critical error flag is generated if at least one of the following errors persists during the "Delay before setting the error" time:
++The "Critical error" signal is generated if at least one of the critical errors (see [[Errors>>doc:Battery management systems.Additional information.2\. Strings controllers\: signals and errors.WebHome||anchor="HErrors"]]) is generated during the “Delay before setting the error” time.
--* «Battery cover»;
--* «Insulation fault»;
--* «CH contactor feedback error»;
--* «DCH contactor feedback error»;
--* «CH/DCH contactor feedback error»;
--* «Module offline».
--
--The critical error flag is cleared if there are no errors from the list above during the "Delay before clearing the error" time.
--
--(% class="box warningmessage" %)
--(((
--**When the critical error flag is present, all battery contactors open.**
--)))
++The “Critical error" signal is cleared if there are no errors from the list above during the “Delay before clearing the error” time.

1740756362809-292.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+20.4 KB

Content

Changes for page 3.4 Protections

Summary

Details

Applications

Navigation

Table of Contents