Changes for page 3.3 Control

Last modified by Admin on 2025/06/11 15:52

From 27.1 to 28.1

From version 28.1

edited by Admin
on 2025/06/11 15:51

Change comment: Uploaded new attachment "1749657087238-544.png", version {1}

To version 30.1

edited by Admin
on 2025/06/11 15:52

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)
Attachments (0 modified, 1 added, 0 removed)
- 1749657114587-360.png

Details

Page properties

Content

@@ -170,7 +170,7 @@
  The battery charge management is configured in the "Control - Charge" section:
--[[image:1740750130950-113.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="219" width="800"]]
++[[image:1749657043032-397.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="253" width="800"]]
  In this section:
@@ -183,12 +183,15 @@
  * Allowable battery current to rejoin modules – a battery current at which joining of battery modules is permitted, A;
  * Allowable voltage difference to rejoin modules – a difference between the voltage of the disconnected module and the battery voltage at which its joining is permitted, V;
  * Checking voltages time – a time of checking voltages of battery modules before starting joining modules, millisecond;
--* Balancing modules time – a time of balancing battery modules after joining modules and before closing main charging contactor, millisecond;
++* Module balancing time – a time of balancing battery modules after joining modules and before closing main charging contactor, millisecond;
++* Interrupt balancing when modules are joined – a flag to break balancing time after all modules are joined;
  * Control the precharging contactor – a flag to control the main precharging contactor;
  * Canceling charging time – a delay before opening the main charging contactor, ms;
  * Disconnect modules that are not ready to charge – a flag for disconnecting modules that have the “Ready to charge” signal cleared.
  * Disconnect all modules if one is not ready to charge – a flag for disconnecting all modules if any of the modules have the “Ready to charge” signal cleared;
  * Join modules on the “Charge request” signal – a flag to enable automatic modules joining if “Charge request” signal appears;
++* Regulator: Keep battery module currents below limits – a flag to enable regulation of module currents to be below module current limit;
++* Regulator: Gain – a gain of current regulator;
  * Maximum charge current limit – a maximum allowed charging current of all battery, A;
  * Errors to disconnect all battery modules – errors that cause all battery modules to be disconnected from the common bus;
  * Errors to open the charging contactor – errors that cause the main charging contactor "Charging" to open;
@@ -228,8 +228,9 @@
  The battery discharge management is configured in the "Control - Discharge" section:
--[[image:1740750247231-926.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="218" width="800"]]
++[[image:1749657087238-544.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="250" width="800"]]
++
  In this section:
  * Enable – a flag to enable battery discharge controller;
@@ -241,12 +241,15 @@
  * Allowable battery current to rejoin modules – a battery current at which joining of battery modules is permitted, A;
  * Allowable voltage difference to rejoin modules – a difference between the voltage of the disconnected module and the battery voltage at which its joining is permitted, V;
  * Checking voltages time – a time of checking voltages of battery modules before starting joining modules, millisecond;
--* Balancing modules time – a time of balancing battery modules after joining modules and before closing main discharging contactor, millisecond;
++* Module balancing time – a time of balancing battery modules after joining modules and before closing main discharging contactor, millisecond;
++* Interrupt balancing when modules are joined – a flag to break balancing time after all modules are joined;
  * Control the precharging contactor – a flag to control the main precharging contactor;
  * Canceling discharging time – a delay before opening the main discharging contactor, millisecond;
  * Disconnect modules that are not ready to discharge – a flag for disconnecting modules that have the “Ready to discharge” signal cleared.
  * Disconnect all modules if one is not ready to discharge – a flag for disconnecting all modules if one of the modules have the “Ready to discharge” signal cleared;
  * Join modules on the “Discharge request” signal – a flag to enable automatic modules joining if “Discharge request” signal appears;
++* Regulator: Keep battery module currents below limits – a flag to enable regulation of module currents to be below module current limit;
++* Regulator: Gain – a gain of current regulator;
  * Maximum discharge current limit – a maximum allowed discharging current of all the battery, A;
  * Errors to disconnect all battery modules – errors that cause all battery modules to be disconnected from the common bus;
  * Errors to open the discharging contactor – errors that cause the main discharging contactor "Discharging" to open,
@@ -294,7 +294,7 @@
  The charge/discharge contactor control is configured in the “Control → Charge/Discharge” section:
--[[image:1740750424118-190.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="250" width="800"]]
++[[image:1749657114587-360.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="284" width="800"]]
  In this section:
@@ -310,7 +310,8 @@
  * Allowable battery current to rejoin modules – a battery current at which joining of battery modules is permitted, A;
  * Allowable voltage difference to rejoin modules – a difference between the voltage of the disconnected module and the battery voltage at which its joining is permitted, V;
  * Checking voltages time – a time of checking voltages of battery modules before starting joining modules, millisecond;
--* Balancing modules time – a time of balancing battery modules after joining modules and before closing main discharging contactor, millisecond;
++* Module balancing time – a time of balancing battery modules after joining modules and before closing main discharging contactor, millisecond;
++* Interrupt balancing when modules are joined – a flag to break balancing time after all modules are joined;
  * Control the precharging contactor – a flag to control the main precharging contactor;
  * Canceling discharging time – a delay before opening the main discharging contactor, millisecond;
  * Disconnect modules that are not ready to charge – a flag for disconnecting modules that have the “Ready to charge” signal cleared;
@@ -317,6 +317,8 @@
  * Disconnect modules that are not ready to discharge – a flag for disconnecting modules that have the “Ready to discharge” signal cleared;
  * Join modules on the “Charge request” signal – a flag to enable automatic modules joining if “Charge request” signal appears;
  * Join modules on the “Discharge request” signal – a flag to enable automatic modules joining if “Discharge request” signal appears;
++* Regulator: Keep battery module currents below limits – a flag to enable regulation of module currents to be below module current limit;
++* Regulator: Gain – a gain of current regulator;
  * Maximum charge current limit – a maximum allowed charging current of all the battery, A;
  * Maximum discharge current limit – a maximum allowed discharging current of all the battery, A;
  * Errors to disconnect all battery modules – errors that cause all battery modules to be disconnected from the common bus;

1749657114587-360.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+58.3 KB

Content

Changes for page 3.3 Control

Summary

Details

Applications

Navigation

Table of Contents