Skip to Content
Last modified by Admin on 2025/03/18 12:50
From version 2.1
edited by Admin
on 2024/12/16 13:25
Change comment: There is no comment for this version
To version 3.1
edited by Admin
on 2024/12/16 13:28
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -65,11 +65,9 @@
65 65  
66 66  [[image:1734355346488-798.png||data-xwiki-image-style-alignment="center"]]
67 67  
68 -1.
69 -
70 70  === Х5 – header for CAN (EXT) interface ===
71 71  
72 -[[image:file:///C:/Users/INASIB~~1/AppData/Local/Temp/msohtmlclip1/01/clip_image001.emz]][[image:1734355229969-197.png||data-xwiki-image-style-alignment="center"]]
70 +[[image:1734355229969-197.png||data-xwiki-image-style-alignment="center"]]
73 73  
74 74  |**Pin**|**Name**|**Description**
75 75  |**1**|**СAN_EXT_H**|CAN-H line of the external CAN bus (communication with a top-level system)
... ... @@ -77,4 +77,56 @@
77 77  |**3**|**CAN_EXT_5V**|Isolated 5V power supply for external devices, max 200 mA
78 78  |**4**|**CAN_EXT_GND**|Isolated ground
79 79  
78 +=== J2 – jumper for switching CAN (EXT) terminal resistor ===
79 +
80 +To connect the terminal resistor between the** CAN_EXT_H** and **CAN_EXT_L** lines, install the jumper J2 according to the following figure:
81 +
82 +[[image:1734355346488-798.png||data-xwiki-image-style-alignment="center"]]
83 +
84 +=== Х6 – header for sold-state relays ===
85 +
86 +[[image:1734355584041-898.jpeg||data-xwiki-image-style-alignment="center" height="65" width="90"]]
87 +
88 +|**Pin**|**Name**|**Description**
89 +|**1**|**NO1**|Normally open contact of the relay 1
90 +|**2**|**NO2**|Normally open contact of the relay 2
91 +|**3**|**NO3**|Normally open contact of the relay 3
92 +|**4**|**COM1**|Common contact of the relay 1 (55V, 2A)
93 +|**5**|**COM2**|Common contact of the relay 2 (55V, 2A)
94 +|**6**|**COM3**|Common contact of the relay 3 (55V, 2A)
95 +
96 +=== X7 – header for discrete inputs/outputs ===
97 +
98 +[[image:1734355584043-416.jpeg||data-xwiki-image-style-alignment="center" height="80" width="263"]]
99 +
100 +|**Pin**|**Name**|**Description**
101 +|**1**|**GND**|Discrete input 1 “dry contact” (ground)
102 +|**2**|**GND**|Discrete input 2 “dry contact” (ground)
103 +|**3**|**GND**|Discrete input 3 “dry contact” (ground)
104 +|**4**|**GND**|Discrete input 4 “dry contact” (ground)
105 +|**5**|**-**|-
106 +|**6**|**GND**|Discrete output 1 (ground)
107 +|**7**|**GND**|Discrete output 2 (ground)
108 +|**8**|**GND**|Discrete output 3 (ground)
109 +|**9**|**GND**|Discrete output 4 (ground)
110 +|**10**|**D_IN1**|Discrete input 1 “dry contact” (+5V)
111 +|**11**|**D_IN2**|Discrete input 2 “dry contact” (+5V)
112 +|**12**|**D_IN3**|Discrete input 3 “dry contact” (+5V)
113 +|**13**|**D_IN4**|Discrete input 4 “dry contact” (+5V)
114 +|**14**|**-**|-
115 +|**15**|**D_OUT1**|Discrete output 1 (+5V, 20mA)
116 +|**16**|**D_OUT2**|Discrete output 2 (+5V, 20mA)
117 +|**17**|**D_OUT3**|Discrete output 3 (+5V, 20mA)
118 +|**18**|**D_OUT4**|Discrete output 4 (+5V, 20mA)
119 +
120 +=== Х8 – header for temperature sensors ===
121 +
122 +[[image:1734355229969-197.png||data-xwiki-image-style-alignment="center"]]
123 +
124 +|**Pin**|**Name**|**Description**
125 +|**1**|**TEMPG1**|Ground of the thermistor 1
126 +|**2**|**TEMPG2**|Ground of the thermistor 2
127 +|**3**|**TEMP1**|Signal from the thermistor 1
128 +|**4**|**TEMP2**|Signal from the thermistor 2
129 +
80 80  
1734355584041-898.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +12.0 KB
Content
1734355584043-416.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +24.8 KB
Content