Skip to Content

Changes for page 3.3 Control

Last modified by Admin on 2025/05/30 16:50
From version 23.1
edited by Admin
on 2025/02/19 14:57
Change comment: There is no comment for this version
To version 21.1
edited by Admin
on 2025/02/19 14:46
Change comment: Uploaded new attachment "1739976370994-390.png", version {1}

Summary

Details

Page properties
Content
... ... @@ -18,15 +18,15 @@
18 18  
19 19  Flags for enabling battery modules are configured in the "Control → Modules → Enable (modules 1 to 8)" and "Control → Modules → Enable (modules 9 to 32)" section:
20 20  
21 +[[image:1734023979582-179.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="165" width="600"]]
21 21  
22 -[[image:1739976358691-364.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="164" width="600"]]
23 23  The network addresses of the battery modules are configured in the "Control → Modules → Node IDs (modules 1 to 8)” and "Control → Modules → Node IDs (modules 9 to 32)”:
24 24  
25 +[[image:1734023979583-589.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="186" width="600"]]
25 25  
26 -[[image:1739976370994-390.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="167" width="600"]]
27 27  Each module in a battery must have a unique address. You can change the address in the battery module settings in the “Connectivity → CAN” section of the BMS Main 3 settings.
28 28  
29 -In corresponding section you can set up minimum number of found modules to finish initialization.
29 +In corresponding section you can set up maximum number of found modules to finish initialization.
30 30  
31 31  === Calculation of battery parameters ===
32 32  
... ... @@ -57,18 +57,18 @@
57 57  * Always on;
58 58  * Automatic, when the main contactor closes by the internal charging and discharging algorithms at the same time with Precharging, Charging, Discharging and Charging/Discharging contactors.
59 59  
60 -In “Always on” mode main contactor closes if all the following is true:
60 +In “Always on” mode, the main contactor closes if all the following is true:
61 61  
62 -* Other contactors are open;
63 -* There are no errors from the "Errors 1, 2 ..." bitfileds.
62 +* “Charging” contactor is open;
63 +* “Discharging” contactor is open;
64 +* there are no errors.
64 64  
65 -In “Always on” mode main contactor opens if all the following is true:
66 +In “Always on” mode, the main contactor opens if “Charging” and “Discharging” contactors are open and any of the following is true:
66 66  
67 -* Other contactors are open;
68 -* There is an error from the the "Errors 1, 2 ..." bitfileds.
68 +* “Charging current present” is set;
69 +* “Discharging current present” is set;
70 +* one or more errors persist.
69 69  
70 -In “Automatic” mode, the main contactor closes by internal algorithms at the same time with other contactors.
71 -
72 72  To change the parameters of the main contactor, select the "Control → Main contactor" section:
73 73  
74 74  [[image:1734024131196-608.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="94" width="600"]]