Changes for page 4.2 Battery

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -75,5 +75,51 @@
75	75	* Total energy regen - total energy received by the battery modules during recuperation, Wh;
76	76	* Total balanced energy – total energy dissipated by the battery modules on balancing resistors, Wh;
77	77	* Input signals – a bitfield including input signals (see [[Input signals>>doc:Battery management systems.Additional information.1\. Battery controllers\: signals and errors.WebHome||anchor="HInputsignals"]]);
78		-* Internal signals – a bitfield including device internal signals (see [[Internal signals>>doc:Battery management systems.Additional information.1\. Battery controllers\: signals and errors.WebHome||anchor="HInternalsignals"]]);
79		-* Errors 1, 2 – errors of the battery (see see [[Errors>>doc:Battery management systems.Additional information.1\. Battery controllers\: signals and errors.WebHome||anchor="HErrors"]]).
	78	+* Internal signals – device internal signals:
	79	+* Errors 1 – errors of the battery 1:
	80	+** Overcurrent;
	81	+** Undervoltage;
	82	+** Overvoltage;
	83	+** Low temperature (DCH) – temperature is too low for discharging;
	84	+** High temperature (DCH) – temperature is too high for discharging;
	85	+** Battery cover error – battery cover is open;
	86	+** High humidity – humidity of the battery is increased;
	87	+** Water – there is water in the battery enclosure;
	88	+** High Logic temperature – at least one of the Logic devices is overheated;
	89	+** Logic offline – at least one of the Logic devices is offline;
	90	+** Critical error;
	91	+** Crown error – connection with a Crown forklift is lost;
	92	+** Cell count error – number of cells does not match the specified value;
	93	+** HYG offline – connection with a HYG forklift is lost;
	94	+** Need acknowledge – there is an unacknowledged error in Error journal;
	95	+** Combilift offline – connection with a Combilift forklift is lost;
	96	+** Short circuit;
	97	+** High contactor temperature;
	98	+** ADC error – current cannot be measured;
	99	+** Current sensor error – error in the current sensor circuit;
	100	+** CH contactor cycles error – switching frequency of the charging contactor is too high;
	101	+** DCH contactor cycles error – switching frequency of the discharging contactor is too high;
	102	+** Shunt offline – connection with the shunt current sensor is lost;
	103	+** Shunt error – internal error of the shunt current sensor;
	104	+** WDT reset – watchdog timer reset the device;
	105	+** No temperature sensors – the device has no temperature sensors connected;
	106	+** Temperature sensor is shorted – some temperature sensors are shorted;
	107	+** Spirit offline – connection with a Spirit forklift is lost;
	108	+* Errors 2 – errors of the battery 2:
	109	+** Low temperature (CH) – temperature is too low for charging;
	110	+** High temperature (CH) – temperature is too high for charging;
	111	+** Unallowable charging – charging the battery through the discharging contactor;
	112	+** Stuck contactor;
	113	+** CH contactor feedback error – the control signals for the charging contactor and the contactor feedback differ;
	114	+** DCH contactor feedback error – the control signals for the discharging contactor and the contactor feedback differ;
	115	+** Insulation fault;
	116	+** PCH contactor feedback error – the control signals for the precharging contactor and the contactor feedback differ;
	117	+** CH/DCH contactor feedback error – the control signals for the charging/discharging contactor and the contactor feedback differ;
	118	+** Main contactor feedback error – the control signals for the main contactor and the contactor feedback differ;
	119	+** General error;
	120	+** High voltage fault – failure of high voltage measuring circuits;
	121	+** Power switch error – short circuit in contactor coil control circuit or power switch overheating;
	122	+** HVIL error – breakage of high-voltage interlock current loop;
	123	+** Precharge error – capacitive load pre-charge process did not end during the estimated time;
	124	+** Power fault – external devices power supply error: current sensors, HVIL, BMS Logic or CAN2 (int) bus powered devices;
	125	+** Current limit error – charging or discharging current is more than limit calculated by Charge map or Discharge map.