Skip to Content

Changes for page 4.2 Battery

Last modified by Admin on 2025/06/19 11:13
From version 16.1
edited by Admin
on 2025/06/19 11:13
Change comment: There is no comment for this version
To version 7.2
edited by Admin
on 2025/02/11 15:00
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -6,12 +6,11 @@
6 6  
7 7  Battery parameters are summarized in the "Battery" section:
8 8  
9 -[[image:1750331506968-446.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="562" width="800"]]
9 +[[image:1735228916836-719.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="370" width="800"]]
10 10  
11 11  In this section:
12 12  
13 -* Voltage (sum of cell voltages) – voltage of the battery, defined as sum of all cell voltages, V;
14 -* Voltage – voltage of the battery, measured before contactors, V;
13 +* Voltage – voltage of the battery, V;
15 15  * Current – current of the battery, A;
16 16  * Internal resistance – internal resistance of the battery, Ohm;
17 17  * Main voltage – supply voltage on the BMS, V;
... ... @@ -21,7 +21,6 @@
21 21  * Temperature 1, 2 – temperature measured by the external temperature sensors, °C;
22 22  * Number of Logic devices – number of connected Logic devices;
23 23  * Logic command rate – number of commands transmitted to Logic devices, com/s;
24 -* Logic retry attempts – amount of BMS Logic retry attempts;
25 25  * Minimum Logic temperature – minimum temperature among Logic devices, °C;
26 26  * Min. Logic temp.: Logic index – number of Logic with minimum temperature;
27 27  * Maximum Logic temperature – minimum temperature among Logic devices, °C;
... ... @@ -34,7 +34,6 @@
34 34  * Maximum cell temperature, °C;
35 35  * Max. cell temp.: Logic index  – number of Logic with maximum cell temperature;
36 36  * Max. cell temp.: cell index – number of cell with maximum temperature;
37 -* Average cell voltage, V;
38 38  * Minimum cell voltage, V;
39 39  * Min. cell volt.: Logic index – number of Logic with minimum voltage;
40 40  * Min. cell volt.: cell index – number of cell with minimum voltage;
... ... @@ -57,7 +57,7 @@
57 57  ** Relaxed (after charging) – battery is in a state of relaxation after charging;
58 58  * Duration – duration of the battery in the "State" state, s;
59 59  * SOC – state of charge of the battery, %;
60 -* DOD – depth of discharge of the battery, A×h;
57 +* DOD – depth of discharge of the battery, %;
61 61  * SOH – state of health of the battery, %;
62 62  * Balancing efficiency – balancing efficiency of the battery, %;
63 63  * Effective capacity, А×h;
... ... @@ -78,5 +78,51 @@
78 78  * Total energy regen - total energy received by the battery modules during recuperation, Wh;
79 79  * Total balanced energy – total energy dissipated by the battery modules on balancing resistors, Wh;
80 80  * Input signals – a bitfield including input signals (see [[Input signals>>doc:Battery management systems.Additional information.1\. Battery controllers\: signals and errors.WebHome||anchor="HInputsignals"]]);
81 -* Internal signals – a bitfield including device internal signals (see [[Internal signals>>doc:Battery management systems.Additional information.1\. Battery controllers\: signals and errors.WebHome||anchor="HInternalsignals"]]);
82 -* Errors 1, 2 – errors of the battery (see [[Errors>>doc:Battery management systems.Additional information.1\. Battery controllers\: signals and errors.WebHome||anchor="HErrors"]]).
78 +* Internal signals – device internal signals:
79 +* Errors 1 – errors of the battery 1:
80 +** Overcurrent;
81 +** Undervoltage;
82 +** Overvoltage;
83 +** Low temperature (DCH) – temperature is too low for discharging;
84 +** High temperature (DCH) – temperature is too high for discharging;
85 +** Battery cover error – battery cover is open;
86 +** High humidity – humidity of the battery is increased;
87 +** Water – there is water in the battery enclosure;
88 +** High Logic temperature – at least one of the Logic devices is overheated;
89 +** Logic offline – at least one of the Logic devices is offline;
90 +** Critical error;
91 +** Crown error – connection with a Crown forklift is lost;
92 +** Cell count error – number of cells does not match the specified value;
93 +** HYG offline – connection with a HYG forklift is lost;
94 +** Need acknowledge – there is an unacknowledged error in Error journal;
95 +** Combilift offline – connection with a Combilift forklift is lost;
96 +** Short circuit;
97 +** High contactor temperature;
98 +** ADC error – current cannot be measured;
99 +** Current sensor error – error in the current sensor circuit;
100 +** CH contactor cycles error – switching frequency of the charging contactor is too high;
101 +** DCH contactor cycles error – switching frequency of the discharging contactor is too high;
102 +** Shunt offline – connection with the shunt current sensor is lost;
103 +** Shunt error – internal error of the shunt current sensor;
104 +** WDT reset – watchdog timer reset the device;
105 +** No temperature sensors – the device has no temperature sensors connected;
106 +** Temperature sensor is shorted – some temperature sensors are shorted;
107 +** Spirit offline – connection with a Spirit forklift is lost;
108 +* Errors 2 – errors of the battery 2:
109 +** Low temperature (CH) – temperature is too low for charging;
110 +** High temperature (CH) – temperature is too high for charging;
111 +** Unallowable charging – charging the battery through the discharging contactor;
112 +** Stuck contactor;
113 +** CH contactor feedback error – the control signals for the charging contactor and the contactor feedback differ;
114 +** DCH contactor feedback error – the control signals for the discharging contactor and the contactor feedback differ;
115 +** Insulation fault;
116 +** PCH contactor feedback error – the control signals for the precharging contactor and the contactor feedback differ;
117 +** CH/DCH contactor feedback error – the control signals for the charging/discharging contactor and the contactor feedback differ;
118 +** Main contactor feedback error – the control signals for the main contactor and the contactor feedback differ;
119 +** General error;
120 +** High voltage fault – failure of high voltage measuring circuits;
121 +** Power switch error – short circuit in contactor coil control circuit or power switch overheating;
122 +** HVIL error – breakage of high-voltage interlock current loop;
123 +** Precharge error – capacitive load pre-charge process did not end during the estimated time;
124 +** Power fault – external devices power supply error: current sensors, HVIL, BMS Logic or CAN2 (int) bus powered devices;
125 +** Current limit error – charging or discharging current is more than limit calculated by Charge map or Discharge map.
1750331354204-418.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -92.3 KB
Content
1750331506968-446.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -92.3 KB
Content