Wiki source code of 4.1 Signals
Last modified by Admin on 2025/02/11 17:36
Show last authors
| author | version | line-number | content |
|---|---|---|---|
| 1 | (% data-numbered-headings-start="4" style="--numbered-headings-start: 3;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %) | ||
| 2 | = Monitoring = | ||
| 3 | |||
| 4 | (% data-numbered-headings-start="1" style="--numbered-headings-start: 0;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %) | ||
| 5 | == Signals == | ||
| 6 | |||
| 7 | States of the KEYRUN and CHARGE_ON signals are available in the "Signals" section. | ||
| 8 | |||
| 9 | States of the device's discrete inputs are available in the "Signals → Input discrete signal" section: | ||
| 10 | |||
| 11 | [[image:1739295295106-897.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="200" width="800"]] | ||
| 12 | |||
| 13 | In this section: | ||
| 14 | |||
| 15 | * Input #1 - Input #8 – physical states of the inputs 1-4 respectively. | ||
| 16 | |||
| 17 | The states of the discrete output signals are available in the "Signals → Output discrete signals" section: | ||
| 18 | |||
| 19 | [[image:1739295317402-295.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="159" width="800"]] | ||
| 20 | |||
| 21 | In this section: | ||
| 22 | |||
| 23 | * Output #1 - Output #4 – physical states of the outputs 1-4 respectively. | ||
| 24 | |||
| 25 | The states of the power switches are available in the "Signals → Power switches" section: | ||
| 26 | |||
| 27 | [[image:1739295355873-803.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="169" width="800"]] | ||
| 28 | |||
| 29 | In this section: | ||
| 30 | |||
| 31 | * Power switch #1 - Power switch #6 – physical states of the power switches 1-6 respectively. | ||
| 32 | |||
| 33 | === Current sensor === | ||
| 34 | |||
| 35 | The states of the current sensors are available in the "Signals → Current sensor" section: | ||
| 36 | |||
| 37 | [[image:1733402780557-330.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="217" width="800"]] | ||
| 38 | |||
| 39 | In this section: | ||
| 40 | |||
| 41 | * Sensor 1, 2, 3: IN1 – output signal from the current sensor, V; | ||
| 42 | * Sensor 1, 2, 3: REF_IN2 – signal in the reference line, V; | ||
| 43 | * Sensor 1, 2, 3: Value – calculated value of the current, A; | ||
| 44 | * Sensor 1, 2, 3: Low range – calculated value of the lower range current, A. | ||
| 45 | |||
| 46 | === Shunt sensor === | ||
| 47 | |||
| 48 | The state of the shunt sensor is available in the "Signals → Shunt sensor" section: | ||
| 49 | |||
| 50 | [[image:1733402780565-376.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="120" width="800"]] | ||
| 51 | |||
| 52 | In this section: | ||
| 53 | |||
| 54 | * Online – a flag showing that the communication with the BMS Current Sensor is established; | ||
| 55 | * Errors – a list of internal errors of the shunt sensor; | ||
| 56 | * Current – an instantaneous value of current measured by the BMS Current Sensor, A (measuring frequency is 50 Hz); | ||
| 57 | * Current (mean) – a mean value of current measured by the BMS Current Sensor, A (the value is calculated as an average of 100 consistent measurements); | ||
| 58 | * Temperature – a temperature of the shunt sensor, °C. | ||
| 59 | |||
| 60 | === HVIL === | ||
| 61 | |||
| 62 | The state of the HVIL is available in the "Signals → HVIL" section: | ||
| 63 | |||
| 64 | [[image:1733402780566-996.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="95" width="800"]] | ||
| 65 | |||
| 66 | In this section: | ||
| 67 | |||
| 68 | * Current (power off) – high voltage interlock loop current at power off, A; | ||
| 69 | * Current (power on) – high voltage interlock loop current at power on, A. |