Changes for page 3.5 External equipment

Last modified by Admin on 2025/06/19 12:32

From 3.1 to 2.1

From version 2.1

edited by Admin
on 2024/12/04 16:59

Change comment: There is no comment for this version

To version 1.1

edited by Admin
on 2024/12/04 16:49

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -1,16 +1,16 @@
--(% data-numbered-headings-start="3" style="--numbered-headings-start: 2;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
--= Settings =
++
--(% data-numbered-headings-start="3" style="--numbered-headings-start: 2;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
--== External equipment ==
  The BMS Main 3 device supports joint operation with chargers, inverters, indication panels, trucks and vehicle controllers.
--=== J1939 charger ===
++1.
++11.
++111. J1939 charger
++
  To change the parameters of communication with a charger using J1939 protocol, select the "External equipment → Chargers → J1939 charger" section:
--[[image:1733330925860-611.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="191" width="800"]]
++[[image:1733330925860-611.png]]
  In this section:
@@ -43,11 +43,14 @@
  The BMS sends a command to charge the battery if the "Allow charging" flag is set (see section 2.3.11).
--=== Eltek charger ===
++1.
++11.
++111. Eltek charger
++
  To change the communication parameters with an Eltek charger, select the "External equipment → Chargers → Eltek charger" section:
--[[image:1733330925864-261.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="129" width="800"]]
++[[image:1733330925864-261.png]]
  In this section:
@@ -66,11 +66,14 @@
  The BMS sends a command to charge the battery if the "Allow charging" flag is set (see section 2.3.11).
--=== MicroPower charger ===
++1.
++11.
++111. MicroPower charger
++
  To change the parameters of communication with a MicroPower charger, select the "External equipment → Chargers → MicroPower charger" section:
--[[image:1733330925865-294.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="149" width="800"]]
++[[image:1733330925865-294.png]]
  In this section:
@@ -91,21 +91,18 @@
  The BMS sends a command to charge the battery if the "Allow charging" flag is set (see section 2.3.11).
--(% class="box warningmessage" %)
--(((
--**Warning! **To work properly with the charger, it is necessary to turn on sending synchronization messages over the CANopen network (see section 2.5.2).
--)))
++**Warning! To work properly with the charger, it is necessary to turn on sending synchronization messages over the CANopen network (see section 2.5.2).**
--(% class="box infomessage" %)
--(((
--After changing the settings, restart the BMS Main 3 device.
--)))
++**After changing the settings, restart the BMS Main 3 device.**
--=== S.P.E. charger ===
++1.
++11.
++111. S.P.E. charger
++
  To change the parameters of communication with an S.P.E. charger, select the "External equipment → Chargers → SPE charger" section:
--[[image:1733330934850-187.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="120" width="800"]]
++[[image:1733330934850-187.png]]
  In this section:
@@ -123,11 +123,14 @@
  The BMS sends a command to charge the battery if the "Allow charging" flag is set (see section 2.3.11).
--=== Bassi charger ===
++1.
++11.
++111. Bassi charger
++
  To change the parameters of communication with a Bassi charger, select the "External equipment → Chargers → Bassi charger" section:
--[[image:1733330934853-223.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="138" width="800"]]
++[[image:1733330934853-223.png]]
  In this section:
@@ -146,16 +146,16 @@
  The BMS sends a command to charge the battery if the "Allow charging" flag is set (see section 2.3.11).
--(% class="box infomessage" %)
--(((
--After changing the settings, restart the BMS Main 3 device.
--)))
++**After changing the settings, restart the BMS Main 3 device.**
--=== ATIB charger ===
++1.
++11.
++111. ATIB charger
++
  To change the parameters of communication with an ATIB Elettronica charger, select the "External equipment → Chargers → ATIB Elettronica charger" section:
--[[image:1733330934855-541.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="116" width="800"]]
++[[image:1733330934855-541.png]]
  In this section:
@@ -173,16 +173,15 @@
  The BMS sends a command to charge the battery if the "Allow charging" flag is set (see section 2.3.11).
--(% class="box infomessage" %)
--(((
--After changing the settings, restart the BMS Main 3 device.
--)))
++**After changing the settings, restart the BMS Main 3 device.**
--=== Fronius charger ===
++1.
++11.
++111. Fronius charger
  To change the parameters of communication with a Fronius charger, select the "External equipment → Chargers → Fronius charger" section:
--[[image:1733330947593-954.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="139" width="800"]]
++[[image:1733330947593-954.png]]
  In this section:
@@ -202,16 +202,16 @@
  The BMS sends a command to charge the battery if the "Allow charging" flag is set (see section 2.3.11).
--(% class="box infomessage" %)
--(((
--After changing the settings, restart the BMS Main 3 device.
--)))
++**After changing the settings, restart the BMS Main 3 device.**
--=== Webasto charger ===
++1.
++11.
++111. Webasto charger
++
  To change the parameters of communication with a Webasto charger, select the "External equipment → Chargers → Webasto charger" section:
--[[image:1733330947595-790.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="107" width="800"]]
++[[image:1733330947595-790.png]]
  In this section:
@@ -228,16 +228,16 @@
  The BMS sends a command to charge the battery if the "Allow charging" flag is set (see section 2.3.11).
--(% class="box infomessage" %)
--(((
--After changing the settings, restart the BMS Main 3 device.
--)))
++**After changing the settings, restart the BMS Main 3 device.**
--=== Skytronic charger ===
++1.
++11.
++111. Skytronic charger
++
  To change the parameters of communication with a Skytronic charger, select the "External equipment → Chargers → Skytronic charger" section:
--[[image:1733330947596-629.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="106" width="800"]]
++[[image:1733330947596-629.png]]
  In this section:
@@ -250,11 +250,14 @@
  * Charge current – maximum charging current, A;
  * Set “Charger connected” signal if the charger is online – a flag to generate the “Charger connected” signal if connection with the charger is established.
--=== CCS Fast charge controller ===
++1.
++11.
++111. CCS Fast charge controller
++
  To change the parameters of communication with a CCS Fast charge controller, select the "External equipment → Chargers → CCS Fast charge controller" section:
--[[image:1733330947597-290.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="287" width="800"]]
++[[image:1733330947597-290.png]]
  In this section:
@@ -284,11 +284,13 @@
  * Number of retries to restart nominal charge – number of retries to restart nominal charge after connection loss with charger;
  * Set “Charger connected” signal if the charger is online – a flag to generate the “Charger connected” signal if connection with the charger is established.
--=== Sunny Island inverter ===
++1.
++11.
++111. Sunny Island inverter
  To change the communication parameters with an SMA Sunny Island inverter, select the "External equipment → Inverters and loads → SMA Sunny Island inverter" section:
--[[image:1733330959804-806.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="141" width="800"]]
++[[image:1733330959804-806.png]]
  In this section:
@@ -306,11 +306,14 @@
  When working with the Sunny Island inverter, the BMS Main 3 device sends messages with the values of voltage and charge/discharge current continuously with the period “Output period”: Charging voltage, Charging current, Discharging voltage, Discharging current.
--=== Pylontech inverter ===
++1.
++11.
++111. Pylontech inverter
++
  To change the parameters of communication with a Pylontech inverter, select the "External equipment → Inverters and loads → Pylontech inverter" section:
--[[image:1733330959806-653.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="119" width="800"]]
++[[image:1733330959806-653.png]]
  In this section:
@@ -326,11 +326,14 @@
  * Discharge voltage (min) – minimum discharging voltage, V;
  * Discharge current – maximum discharging current, А.
--=== ASTOM load bank (cycling) ===
++1.
++11.
++111. ASTOM load bank (cycling)
++
  To change the parameters of communication with a ASTOM load bank, select the "External equipment → Inverters and loads → ASTOM load bank (cycling)" section:
--[[image:1733330959806-204.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="170" width="800"]]
++[[image:1733330959806-204.png]]
  In this section:
@@ -349,13 +349,16 @@
  * Voltage difference – difference between the minimum and maximum cell voltages for error to be generated and cycling to be stopped, V;
  * Delay before setting the error – a delay before generating an error, second.
--=== HYG Class I-III truck ===
++1.
++11.
++111. HYG Class I-III truck
++
  The HYG Class I-III equipment is installed on the forklifts by the group of companies HYSTER-YALE.
  To change communication parameters with HYG Class I-III equipment, select the "External equipment → Trucks and Vehicles → HYG Class I-III truck" section:
--[[image:1733330959808-973.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="234" width="800"]]
++[[image:1733330959808-973.png]]
  In this section:
@@ -383,23 +383,19 @@
  * Send Heartbeat messages – a flag to enable generation of the Heartbeat messages to the forklift;
  * Heartbeat period – Heartbeat sending period, millisecond.
--(% class="box infomessage" %)
--(((
--**Note:** Dependence of the thermal derate from the battery and contactor temperature is linear. The system sends maximum value of the thermal derate among values calculated for the battery temperature and contactor temperature.
--)))
++Note – Dependence of the thermal derate from the battery and contactor temperature is linear. The system sends maximum value of the thermal derate among values calculated for the battery temperature and contactor temperature.
  The device with the identifier “Node ID” continuously transmits control commands to the forklift the with a period of 100 milliseconds.
--(% class="box infomessage" %)
--(((
--After changing the settings, restart the BMS Main 3 device.
--)))
++**After changing the settings, restart the BMS Main 3 device.**
--=== Combilift truck ===
++1.
++11.
++111. Combilift truck
  To change communication parameters with a Combilift forklift, select the "External equipment → Trucks and Vehicles → Combilift truck" section:
--[[image:1733330972246-129.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="171" width="800"]]
++[[image:1733330972246-129.png]]
  In this section:
@@ -419,16 +419,16 @@
  The device with the identifier “Node ID” continuously transmits control commands to the forklift with a period of 200 milliseconds.
--(% class="box infomessage" %)
--(((
--After changing the settings, restart the BMS Main 3 device.
--)))
++**After changing the settings, restart the BMS Main 3 device.**
--=== Spirit AGV ===
++1.
++11.
++111. Spirit AGV
++
  To change communication parameters with a Spirit AeroSystems truck, select the "External equipment → Trucks and Vehicles → Spirit AGV" section:
--[[image:1733330972257-158.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="182" width="800"]]
++[[image:1733330972257-158.png]]
  In this section:
@@ -452,13 +452,16 @@
  The device with the identifier “Node ID” continuously transmits control commands to the truck with a period of 100 milliseconds.
--=== Crown truck ===
++1.
++11.
++111. Crown truck
++
  The BMS Main 3 device uses the BMS Crown adapter to control powering the Crown forklift.
  To change communication parameters with the BMS Crown adapter, select the "External equipment → Trucks and Vehicles → Crown truck" section:
--[[image:1733330972258-463.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="96" width="800"]]
++[[image:1733330972258-463.png]]
  In this section:
@@ -520,16 +520,16 @@
  The value of T is set in the "Delay before starting discharging" field (see section 2.3.12).
--(% class="box infomessage" %)
--(((
--After changing the settings, restart the BMS Main 3 device.
--)))
++**After changing the settings, restart the BMS Main 3 device.**
--=== ZiK truck ===
++1.
++11.
++111. ZiK truck
++
  To change communication parameters with a ZiK truck, select the "External equipment → Trucks and Vehicles → ZiK truck" section:
--[[image:1733330985625-186.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="100" width="800"]]
++[[image:1733330985625-186.png]]
  In this section:
@@ -543,16 +543,16 @@
  The BMS with the identifier “Node ID” continuously transmits control commands to the truck with a period of 100 milliseconds.
--(% class="box infomessage" %)
--(((
--After changing the settings, restart the BMS Main 3 device.
--)))
++**After changing the settings, restart the BMS Main 3 device.**
--=== Evocargo Evo1.1 truck ===
++1.
++11.
++111. Evocargo Evo1.1 truck
++
  To change communication parameters with an Evocargo Evo1.1 truck, select the "External equipment → Trucks and Vehicles → Evocargo Evo1.1 truck" section:
--[[image:1733330985627-145.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="87" width="800"]]
++[[image:1733330985627-145.png]]
  In this section:
@@ -559,11 +559,14 @@
  * Enable – a flag to enable communication with the truck;
  * Receive timeout – a timeout for receiving packets from the truck, millisecond.
--=== BKM vehicle ===
++1.
++11.
++111. BKM vehicle
++
  To change communication parameters with a BKM vehicle, select the "External equipment → Trucks and Vehicles → BKM vehicle" section:
--[[image:1733330985627-310.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="90" width="800"]]
++[[image:1733330985627-310.png]]
  In this section:
@@ -574,13 +574,16 @@
  * Receive timeout – a timeout for receiving packets from the vehicle.
  * Number of Logics in a pack.
--=== Basic J1939 vehicle ===
++1.
++11.
++111. Basic J1939 vehicle
++
  The basic vehicle protocol J1939 is developed by Movicom Electric, and its description is available upon request. Using this protocol, information about the parameters of the battery can be obtained. The protocol also implements the management of battery operation modes.
  Communication parameters via the Basic J1939 protocol are configured in the “External equipment → Trucks and Vehicles → Basic J1939 vehicle” section:
--[[image:1733330996003-704.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="98" width="800"]]
++[[image:1733330996003-704.png]]
  In this section:
@@ -592,11 +592,14 @@
  * Receive vehicle messages – a flag to activate receiving vehicle messages;
  * First vehicle message ID – an identifier of the first message of the vehicle in the J1939 network.
--=== Bender iso165C ===
++1.
++11.
++111. Bender iso165C
++
  To change communication parameters with a Bender iso165C, select the "External equipment → IMD → Bender iso165C" section:
--[[image:1733330996004-140.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="108" width="800"]]
++[[image:1733330996004-140.png]]
  In this section:
@@ -609,11 +609,14 @@
  * Threshold to detect insulation error – threshold resistance value to generate the insulation error, Ohm;
  * Threshold to detect insulation warning – threshold resistance value to generate the insulation warning, Ohm.
--=== BMS IMD ===
++1.
++11.
++111. BMS IMD
++
  To change communication parameters with a BMS IMD, select the "External equipment → IMD → BMD IMD " section:
--[[image:1733330996005-297.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="109" width="800"]]
++[[image:1733330996005-297.png]]
  In this section:
@@ -626,13 +626,16 @@
  * Threshold to detect insulation alarm, Ohm;
  * Threshold to detect insulation warning, Ohm.
--=== Main X ===
++1.
++11.
++111. Main X
++
  The BMS Main 3 device can connect to BMS Main X strings controller.
  Communication parameters with the Main X are configured in the "External equipment → BMS → Main X" section:
--[[image:1733330996006-677.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="106" width="800"]]
++[[image:1733330996006-677.png]]
  In this section:

Changes for page 3.5 External equipment

Summary

Details

Applications

Navigation

Table of Contents