Skip to Content

Changes for page 3.3 Control

Last modified by Admin on 2026/04/30 15:56
From version 87.17
edited by Admin
on 2026/04/02 10:42
Change comment: There is no comment for this version
To version 93.1
edited by Admin
on 2026/04/30 15:52
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -8,7 +8,7 @@
8 8  
9 9  To change the common BMS settings, select the "Control → Common settings" section:
10 10  
11 -[[image:1735054851946-552.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="105" width="800"]]
11 +[[image:1777557373784-459.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="180" width="800"]]
12 12  
13 13  In this section:
14 14  
... ... @@ -489,7 +489,7 @@
489 489  * **Errors 1, 2 to open the charging contactor** – bitfields to choose the errors which will open the charging contactor;
490 490  * **Use custom delays before stopping charging (on errors)** – a flag to enable manual settings of time delays T,,off,, for specific errors;
491 491  * **Custom delay: <error>** – delay for specific error, millisecond;
492 -* **Switch off the charging contactor on errors without delay** – a flag to protectively open the charging contactor without a delay. In the opposite case, when an error is detected, the charging contactor opens always with the delay “Delay before stopping charging”;
492 +* **Switch off the charging contactor on errors without delay** – a flag to protectively open the charging contactor without a delay. In the opposite case, when an error is detected, the charging contactor opens always with the delay “Delay before stopping charging”.
493 493  
494 494  === Discharge ===
495 495  
... ... @@ -563,7 +563,7 @@
563 563  On **Independent (on Charge request or Discharge request)** algorithm "Charging/Discharging" signal is based on its own controller and performs as follows:
564 564  
565 565  * if there is "Charge request" or "Discharge request" signal and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the Charging/Discharging signal is set;
566 -* If the "Charge request" or "Discharge request" disappears or errors occur (see the "Errors 1, 2 ..." bitfields), then after the delay time T,,off,, the "Charging/Discharging" signal is cleared.
566 +* If the "Charge request" and "Discharge request" disappears or errors occur (see the "Errors 1, 2 ..." bitfields), then after the delay time T,,off,, the "Charging/Discharging" signal is cleared.
567 567  
568 568  (% class="box infomessage" %)
569 569  (((
... ... @@ -584,7 +584,7 @@
584 584  * **Delay before starting charging or discharging**, millisecond;
585 585  * **Delay before stopping charging or discharging**, millisecond;
586 586  * **Control the precharging contactor** – a flag that enables control of precharging contactor while closing the charge/discharge contactor;
587 -* **Emulate the "Charging" and "Discharging" signals** – a flag to enable generation of "Charging" and "Discharging" signals in In when closing Charge/Discharge contactor. **DO NOT** use with enabled Charge and Discharge controllers;
587 +* **Emulate the "Charging" and "Discharging" signals** – a flag to enable generation of "Charging" and "Discharging" signals in Independet mode when closing Charge/Discharge contactor. **DO NOT** use with enabled Charge and Discharge controllers;
588 588  * **Errors 1, 2 to prevent CHARGING through charging/discharging contactor, Errors 1, 2 to prevent DISCHARGING through charging/discharging contactor** – bitfields to choose the errors which will open the charging/discharging contactor. This bitfields are combined by bitwise OR and intended to separate settings for charging and discharging processes;
589 589  * **Errors 1, 2 which affect the contactor only if battery CHARGING is detected** – a bitfield to choose the errors which will trigger only if charging current is present. This bitfield is combined with "Errors 1, 2 to prevent CHARGING through charging/discharging contactor" by bitwise AND;
590 590  * **Errors 1, 2 which affect the contactor only if battery DISCHARGING is detected** – a bitfield to choose the errors which will trigger only if discharging current is present. This bitfield is combined with "Errors 1, 2 to prevent DISCHARGING through charging/discharging contactor" by bitwise AND;
1777557373784-459.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +40.4 KB
Content
1777557391157-274.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +40.4 KB
Content