Changes for page 3.3 Control

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -373,9 +373,9 @@
373	373
374	374	(% class="box infomessage" %)
375	375	(((
376		-**Note:** The **"Allow charging"** signal activates under two independent conditions:
	376	+**Note:** The "Allow charging" signal activates under two independent conditions:
377	377	1) the voltage on the cells reaches the “Voltage to reset the “Ready to charge"” level and
378		-2) the "Delay before recharging" time has passed since the clearing of the "Allow charging" signal.
	378	+2) the "Delay before recharging" time has passed since the opening of the allow charging contactor.
379	379	)))
380	380
381	381	=== Discharging status ===
...	...	@@ -444,27 +444,27 @@
444	444
445	445	=== Charge ===
446	446
447		-The BMS Main 3 / BMS Main 2R device connect battery to the charger using the "Charging" signal.
	447	+There are two signals that serve charging the battery: "Charging" and "Allow charging". With the help of the "Allow charging" signal, the BMS commands the charger to start or stop charging.
448	448
449	449	BMS Main 3 / BMS Main 2R supports three charge control algorithms:
450	450
451		-If the "**Always on**" algorithm is selected, the "Сharging" signal is always set. If at least one of the errors from the "Errors 1, 2 ..." bitfields appears or one of the signals:
	451	+If the "**Always on**" algorithm is selected, the "Сharging signals" and the "Allow charging" signals are always set. If at least one of the errors from the "Errors 1, 2 ..." bitfields appears or one of the signals:
452	452
453	453	* Service reset;
454	454	* Power down request;
455	455	* Inhibit charging,
456	456
457		-the "Charging" signal is cleared.
	457	+both signals are cleared.
458	458
459	459	When the algorithm "**On charger connected**" is selected, the control is performed as follows:
460	460
461		-* If there is a signal “Charger connected” and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the "Charging" signal is set;
462		-* If the signal “Charger connected” disappears or errors occur (see the "Errors 1, 2 ..." bitfields), then after the delay time T,,off,, the "Charging" signal is cleared.
	461	+* If there is a signal “Charger connected” and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the "Charging" and the "Allow charging" signal are set;
	462	+* If the signal “Charger connected” disappears or errors occur (see the "Errors 1, 2 ..." bitfields), the "Allow charging" signal is cleared and after the delay time T,,off,, the "Charging" signal is cleared.
463	463
464	464	When the "**On charge request**" algorithm selected, the control is performed as follows:
465	465
466		-* If there is a signal “Charge request” and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the "Charging" signal is set;
467		-* If the signal “Charge request” disappears or errors occur (see the "Errors 1, 2 ..." bitfields), then after the delay time T,,off,, the "Charging" signal is cleared;
	466	+* If there is a signal “Charge request” and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the "Charging" and the "Allow charging" signal are set;
	467	+* If the signal “Charge request” disappears or errors occur (see the "Errors 1, 2 ..." bitfields), the "Allow charging" signal is cleared and after the delay time T,,off,, the "Charging" signal is cleared;
468	468
469	469	(% class="box infomessage" %)
470	470	(((
...	...	@@ -507,17 +507,17 @@
507	507
508	508	If the algorithm "**On charger disconnected**" is selected, the control is performed as follows:
509	509
510		-* if there are no “Charger connected” and "Charging" signals and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the "Discharging" signal is set;
511		-* If the signal “Charger connected” appears or errors occur (see the "Errors 1, 2 ..." bitfields), then after the delay time T,,off,, the "Discharging" signal is cleared.
	510	+* if there is no “Charger connected” and "Charging" signals and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the "Discharging" contactor closes;
	511	+* If the signal “Charger connected” appears or errors occur (see the "Errors 1, 2 ..." bitfields), then after the delay time T,,off,, the discharging contactor opens.
512	512
513	513	When the "**On discharge request**" algorithm selected, the control is performed as follows:
514	514
515		-* if there is signal “Discharge request” and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the "Discharging" signal is set;
516		-* If the signal “Discharge request” disappears or errors occur (see the "Errors 1, 2 ..." bitfields), then after the delay time T,,off,, the "Discharging" signal is cleared.
	515	+* if there is signal “Discharge request”, the charging contactor is open and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the discharging contactor closes;
	516	+* If the signal “Discharge request” disappears or errors occur (see the "Errors 1, 2 ..." bitfields), then after the delay time T,,off,, the discharging contactor opens.
517	517
518	518	(% class="box infomessage" %)
519	519	(((
520		-**Note: **when errors occur in the system, the **"Discharge" **signal is cleared either immediately or with the delay T,,off,, (depends on the settings described below).
	520	+**Note: **when errors occur in the system, the **Discharge **contactor opens either immediately or with the delay T,,off,, (depends on the settings described below).
521	521	)))
522	522
523	523	To change the parameters of the battery discharge control algorithm, select the "Control → Discharge" section:
...	...	@@ -542,16 +542,16 @@
542	542
543	543	=== Charge/Discharge ===
544	544
545		-The BMS Main 3 / BMS Main 2R device can control the contactor, used in power line both used for connecting battery to charger and load, by using the "Charging/Discharging" signal.
	545	+The BMS Main 3 / BMS Main 2R device can control the Charge/Discharge contactor, which combines algorithms of charging and discharging contactor.
546	546
547		-"Charging/Discharging" signal has three algorithms of operation:
	547	+Charge/Discharge contactor has three algorithms of operation:
548	548
549		-On **Dependent (on Charging and Discharging signals)** algorithm the "Charging/Discharging" signal depends on Charge and Discharge controllers and equal to:
	549	+On **Dependent (on Charging and Discharging signals)** algorithm the charge/discharge contactor depends on Charge and Discharge controllers and behaves:
550	550
551		-* "Charging" signal if "Charging" signal is set;
552		-* "Discharging" signal in other cases.
	551	+* as Charging contactor if "Charging" signal is set;
	552	+* as Discharging contactor in other cases.
553	553
554		-When **Independent (Always) **algorithm is selected, the "Charging/Discharging" signal is always set. If at least one of the errors from the "Errors 1, 2 ..." bitfields appears or one of the signals:
	554	+When **Independent (Always) **algorithm is selected, the charging/discharging contactor is always closed. If at least one of the errors from the "Errors 1, 2 ..." bitfields appears or one of the signals:
555	555
556	556	* Service reset
557	557	* Power down request
...	...	@@ -558,12 +558,12 @@
558	558	* Inhibit charging
559	559	* Inhibit discharging
560	560
561		-the Charging/Discharging signal is cleared.
	561	+the charging/discharging contactor opens.
562	562
563		-On **Independent (on Charge request or Discharge request)** algorithm "Charging/Discharging" signal is based on its own controller and performs as follows:
	563	+On **Independent (on Charge request or Discharge request)** algorithm charge/discharge contactor is based on its own controller and performs as follows:
564	564
565		-* if there is "Charge request" or "Discharge request" signal and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the Charging/Discharging signal is set;
566		-* If the "Charge request" or "Discharge request" disappears or errors occur (see the "Errors 1, 2 ..." bitfields), then after the delay time T,,off,, the "Charging/Discharging" signal is cleared.
	565	+* if there is "Charge request" or "Discharge request" signal and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the charging/discharging contactor closes;
	566	+* If the "Charge request" or "Discharge request" disappears or errors occur (see the "Errors 1, 2 ..." bitfields), then after the delay time T,,off,, the charging/discharging contactor opens.
567	567
568	568	(% class="box infomessage" %)
569	569	(((
...	...	@@ -584,7 +584,7 @@
584	584	* **Delay before starting charging or discharging**, millisecond;
585	585	* **Delay before stopping charging or discharging**, millisecond;
586	586	* **Control the precharging contactor** – a flag that enables control of precharging contactor while closing the charge/discharge contactor;
587		-* **Emulate the "Charging" and "Discharging" signals** – a flag to enable generation of "Charging" and "Discharging" signals when closing charge/discharge contactor. DO NOT use with enabled Charger and Disc;
	587	+* **Emulate the "Charging" and "Discharging" signals** – a flag to enable generation of "Charging" and "Discharging" signals when closing charge/discharge contactor;
588	588	* **Errors 1, 2 to prevent CHARGING through charging/discharging contactor, Errors 1, 2 to prevent DISCHARGING through charging/discharging contactor** – bitfields to choose the errors which will open the charging/discharging contactor. This bitfields are combined by bitwise OR and intended to separate settings for charging and discharging processes;
589	589	* **Errors 1, 2 which affect the contactor only if battery CHARGING is detected** – a bitfield to choose the errors which will trigger only if charging current is present. This bitfield is combined with "Errors 1, 2 to prevent CHARGING through charging/discharging contactor" by bitwise AND;
590	590	* **Errors 1, 2 which affect the contactor only if battery DISCHARGING is detected** – a bitfield to choose the errors which will trigger only if discharging current is present. This bitfield is combined with "Errors 1, 2 to prevent DISCHARGING through charging/discharging contactor" by bitwise AND;