Skip to Content

Changes for page 3.3 Control

Last modified by Admin on 2026/04/30 15:56
From version 78.3
edited by Admin
on 2026/03/31 14:27
Change comment: There is no comment for this version
To version 78.1
edited by Admin
on 2026/03/31 14:24
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -741,12 +741,11 @@
741 741  Conditions for signal generation:
742 742  
743 743  * the minimum temperature among all cells of the battery is less than the “Minimum cell temperature” value during the “Delay before starting the heater” time;
744 -* there are no errors from "Errors 1, 2..." bitfields.
744 +* there are no errors from** Errors 1, 2**
745 745  
746 746  Conditions for clearing the signal:
747 747  
748 -* the minimum temperature among all cells of the battery is greater than the “Tolerant cell temperature” value during the “Delay before stopping the heater” time;
749 -* there is an error from "Errors 1, 2..." bitfields.
748 +* the minimum temperature among all cells of the battery is greater than the “Tolerant cell temperature” value during the “Delay before stopping the heater” time.
750 750  
751 751  (% class="box infomessage" %)
752 752  (((
... ... @@ -761,24 +761,22 @@
761 761  
762 762  In this section:
763 763  
764 -* **Enable** – a flag to enable the cooler control;
765 -* **Maximum cell temperature**, °C;
766 -* **Tolerant cell temperature**, °C;
767 -* **Delay before starting the cooler**, millisecond;
768 -* **Delay before stopping the cooler**, millisecond;
769 -* **Errors 1, 2 to open the cooler **– bitfields to choose the errors which will open the cooler.
763 +* Enable – a flag to enable the cooler control;
764 +* Maximum cell temperature, °C;
765 +* Tolerant cell temperature, °C;
766 +* Delay before starting the cooler, millisecond;
767 +* Delay before stopping the cooler, millisecond;
768 +* Switch off the cooler contactor on errors (Undervoltage, Overcurrent, Low temperature, Short circuit or Critical error).
770 770  
771 771  As a result of operating the cooling algorithm, the "Cooler" signal is generated.
772 772  
773 773  Conditions for signal generation:
774 774  
775 -* the maximum temperature among all cells of the battery is greater than the “Maximum cell temperature” value during the “Delay before starting the cooler” time;
776 -* there are no errors from "Errors 1, 2..." bitfields.
774 +* the maximum temperature among all cells of the battery is greater than the “Maximum cell temperature” value during the “Delay before starting the cooler” time.
777 777  
778 778  Conditions for clearing the signal:
779 779  
780 -* the maximum temperature among all cells of the battery is less than the “Tolerant cell temperature” value during the “Delay before stopping the cooler” time;
781 -* there is an error from "Errors 1, 2..." bitfields.
778 +* the maximum temperature among all cells of the battery is less than the “Tolerant cell temperature” value during the “Delay before stopping the cooler” time.
782 782  
783 783  (% class="box infomessage" %)
784 784  (((
... ... @@ -787,7 +787,6 @@
787 787  
788 788  === High voltage ===
789 789  
790 -
791 791  The BMS Main 3 device has an ability to measure high voltages before and after contactors.
792 792  
793 793  To change the parameters of high voltage fault, select the "Control → High voltage" section: