Changes for page 3.3 Control

Last modified by Admin on 2026/04/30 15:56

From 77.1 to 77.2 From 78.3 to 78.4

From version 77.2

edited by Admin
on 2026/03/31 14:19

Change comment: There is no comment for this version

To version 78.3

edited by Admin
on 2026/03/31 14:27

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -546,7 +546,7 @@
  Charge/Discharge contactor has three algorithms of operation:
--On **Dependent (on Charging and Discharging signals)** algorithm the charge/discharge contactor depends on Charge and Discharge algorithms and their signals and behaves
++On **Dependent (on Charging and Discharging signals)** algorithm the charge/discharge contactor depends on Charge and Discharge controllers and behaves:
  * as Charging contactor if "Charging" signal is set;
  * as Discharging contactor in other cases.
@@ -560,9 +560,8 @@
  the charging/discharging contactor opens.
++On **Independent (on Charge request or Discharge request)** algorithm charge/discharge contactor is based on its own controller and performs as follows:
--**Independent (on Charge request or Discharge request)** - charge/discharge contactor is based on its own controller and performs as follows:
--
  * if there is "Charge request" or "Discharge request" signal and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the charging/discharging contactor closes;
  * If the "Charge request" or "Discharge request" disappears or errors occur (see the "Errors 1, 2 ..." bitfields), then after the delay time T,,off,, the charging/discharging contactor opens.
@@ -717,10 +717,10 @@
  In this section:
  * **Minimum voltage to power down** – a minimum voltage level of the battery below which the BMS commands to shut down the battery, V;
--* Idle time to power down – a time of battery inactivity after which the battery is shut down, minute;
--* Wait the "Power up/down request" is cleared (on startup) – a flag to enable delay for clearing the “Power up/down request” signal while starting the BMS.
--* Power down if KEYRUN and CHARGE_ON are cleared – a flag to power down the device if KEYRUN and CHARGE_ON signals are cleared;
--* Delay before setting the internal power down signal – a delay before turning off the device power when removing KEYRUN and CHARGE_ON or receiving the “Power down request” command, ms.
++* **Idle time to power down** – a time of battery inactivity after which the battery is shut down, minute;
++* **Wait the "Power up/down request" is cleared (on startup)** – a flag to enable delay for clearing the “Power up/down request” signal while starting the BMS.
++* **Power down if KEYRUN and CHARGE_ON are cleared** – a flag to power down the device if KEYRUN and CHARGE_ON signals are cleared;
++* **Delay before setting the internal power down signal** – a delay before turning off the device power when removing KEYRUN and CHARGE_ON or receiving the “Power down request” command, ms.
  === Heater ===
@@ -730,22 +730,24 @@
  In this section:
--* Enable – a flag to enable the heater control;
--* Minimum cell temperature, °C;
--* Tolerant cell temperature, °C;
--* Delay before starting the heater, millisecond;
--* Delay before stopping the heater, millisecond;
--* Switch off the heater on errors (Undervoltage, Overcurrent, High temperature, Short circuit or Critical error).
++* **Enable **– a flag to enable the heater control;
++* **Minimum cell temperature**, °C;
++* **Tolerant cell temperature**, °C;
++* **Delay before starting the heater**, millisecond;
++* **Delay before stopping the heater**, millisecond;
++* **Errors 1, 2 to open the heater** – bitfields to choose the errors which will open the heater.
  As a result of operating the heating algorithm, the “Heater” signal is generated.
  Conditions for signal generation:
--* the minimum temperature among all cells of the battery is less than the “Minimum cell temperature” value during the “Delay before starting the heater” time.
++* the minimum temperature among all cells of the battery is less than the “Minimum cell temperature” value during the “Delay before starting the heater” time;
++* there are no errors from "Errors 1, 2..." bitfields.
  Conditions for clearing the signal:
--* the minimum temperature among all cells of the battery is greater than the “Tolerant cell temperature” value during the “Delay before stopping the heater” time.
++* the minimum temperature among all cells of the battery is greater than the “Tolerant cell temperature” value during the “Delay before stopping the heater” time;
++* there is an error from "Errors 1, 2..." bitfields.
  (% class="box infomessage" %)
  (((
@@ -760,22 +760,24 @@
  In this section:
--* Enable – a flag to enable the cooler control;
--* Maximum cell temperature, °C;
--* Tolerant cell temperature, °C;
--* Delay before starting the cooler, millisecond;
--* Delay before stopping the cooler, millisecond;
--* Switch off the cooler contactor on errors (Undervoltage, Overcurrent, Low temperature, Short circuit or Critical error).
++* **Enable** – a flag to enable the cooler control;
++* **Maximum cell temperature**, °C;
++* **Tolerant cell temperature**, °C;
++* **Delay before starting the cooler**, millisecond;
++* **Delay before stopping the cooler**, millisecond;
++* **Errors 1, 2 to open the cooler **– bitfields to choose the errors which will open the cooler.
  As a result of operating the cooling algorithm, the "Cooler" signal is generated.
  Conditions for signal generation:
--* the maximum temperature among all cells of the battery is greater than the “Maximum cell temperature” value during the “Delay before starting the cooler” time.
++* the maximum temperature among all cells of the battery is greater than the “Maximum cell temperature” value during the “Delay before starting the cooler” time;
++* there are no errors from "Errors 1, 2..." bitfields.
  Conditions for clearing the signal:
--* the maximum temperature among all cells of the battery is less than the “Tolerant cell temperature” value during the “Delay before stopping the cooler” time.
++* the maximum temperature among all cells of the battery is less than the “Tolerant cell temperature” value during the “Delay before stopping the cooler” time;
++* there is an error from "Errors 1, 2..." bitfields.
  (% class="box infomessage" %)
  (((
@@ -784,6 +784,7 @@
  === High voltage ===
++
  The BMS Main 3 device has an ability to measure high voltages before and after contactors.
  To change the parameters of high voltage fault, select the "Control → High voltage" section:

Changes for page 3.3 Control

Summary

Details

Applications

Navigation

Table of Contents