Changes for page 3.3 Control

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -319,12 +319,12 @@
319	319	In **“Always on”** mode main contactor closes if all the following is true:
320	320
321	321	* Other contactors are open;
322		-* There are __no errors__ from the "Errors 1, 2 ..." bitfileds.
	322	+* There are no errors from the "Errors 1, 2 ..." bitfileds.
323	323
324	324	and opens if all the following is true:
325	325
326	326	* Other contactors are open;
327		-* There is __an error__ from the the "Errors 1, 2 ..." bitfileds.
	327	+* There is an error from the the "Errors 1, 2 ..." bitfileds.
328	328
329	329	In **“Automatic”** mode, the main contactor closes by internal algorithms at the same time with other contactors.
330	330
...	...	@@ -343,13 +343,13 @@
343	343
344	344	* **Enable **– a flag to enable the main contactor control;
345	345	* **Algorithm** – main contactor control algorithm:
346		-** **Always on** – contactor is always closed;
347		-** **Automatic** – contactor closes by internal charge and discharge algorithms;
348		-** **On demand** – contactor is closed by an external request;
349		-* **Time to keep the contactor closed before closing the others** – a time for other contactors to be open after the main contactor is closed;
350		-* **Delay before opening the contactor** – a time which is used to detect conditions for opening the contactor, s;
351		-* **Keep the contactor open until the device is restarted** – a flag for keeping the main contactor open until the system is reset;
352		-* **Errors 1, 2 to open the main contactor** – bitfields to choose the errors which will open the main contactor.
	346	+** Always on – contactor is always closed;
	347	+** Automatic – contactor closes by internal charge and discharge algorithms;
	348	+** On demand – contactor is closed by an external request;
	349	+* Time to keep the contactor closed before closing the others – a time for other contactors to be open after the main contactor is closed;
	350	+* Delay before opening the contactor – a time which is used to detect conditions for opening the contactor, s;
	351	+* Keep the contactor open until the device is restarted – a flag for keeping the main contactor open until the system is reset;
	352	+* Errors 1, 2 to open the main contactor – bitfields to choose the errors which will open the main contactor.
353	353
354	354	=== Charging status ===
355	355
...	...	@@ -359,17 +359,17 @@
359	359
360	360	In this section:
361	361
362		-* **Current to set the "Charging current present"** – a current level to generate the "Charging current present" signal, A;
363		-* **Current to clear the "Charging current present"** – a current level to clear the "Charging current present" signal, A;
364		-* **Voltage to clear the “Ready to charge”** – a threshold U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if the voltage of any cell is above this level, the “Ready to charge” (hence, the “Allow charging”) signal is cleared;
365		-* **Voltage to reset the “Ready to charge”** – a tolerant U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if all cell voltages are below the tolerant level, the “Ready to charge” (hence, the “Allow charging”) signal is set;
366		-* **Use actual voltage to generate the "Ready to charge" signal** – a flag to disable voltage correction for "Ready to charge" signal;
367		-* **Treat negative currents as zero currents for generating the "Ready to charge" signal** – a flag to disable voltage correction for "Ready to charge" signal at discharging current;
368		-* **Delay before recharging** – a time after which the previously opened the allow charging contactor closes again, minute; to disable the operation by timeout set "Delay before recharging" to 0;
369		-* **Check the 'Charge current limit' value to generate the 'Ready to charge'** – a flag to enable check of "Charging current limit" to generate the "Ready to charge" signal;
370		-* **Charge current limit to clear the 'Ready to charge'** – a threshold charging current limit value, A; if the limit is //above //this level, the “Ready to charge” signal is cleared;
371		-* **Charge current limit to set the 'Ready to charge'** – a tolerant charging current limit value, A; if the limit is //below //this level, the “Ready to charge” signal is set;
372		-* **Errors 1, 2 to clear the "Ready to charge"** – bitfields to choose the errors which will clear the "Ready to charge" signal.
	362	+* Current to set the "Charging current present" – a current level to generate the "Charging current present" signal, A;
	363	+* Current to clear the "Charging current present" – a current level to clear the "Charging current present" signal, A;
	364	+* Voltage to clear the “Ready to charge” – a threshold U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if the voltage of any cell is above this level, the “Ready to charge” (hence, the “Allow charging”) signal is cleared;
	365	+* Voltage to reset the “Ready to charge” – a tolerant U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if all cell voltages are below the tolerant level, the “Ready to charge” (hence, the “Allow charging”) signal is set;
	366	+* Use actual voltage to generate the "Ready to charge" signal – a flag to disable voltage correction for "Ready to charge" signal;
	367	+* Treat negative currents as zero currents for generating the "Ready to charge" signal – a flag to disable voltage correction for "Ready to charge" signal at discharging current;
	368	+* Delay before recharging – a time after which the previously opened the allow charging contactor closes again, minute; to disable the operation by timeout set "Delay before recharging" to 0;
	369	+* Check the 'Charge current limit' value to generate the 'Ready to charge' – a flag to enable check of "Charging current limit" to generate the "Ready to charge" signal;
	370	+* Charge current limit to clear the 'Ready to charge' – a threshold charging current limit value, A; if the limit is //above //this level, the “Ready to charge” signal is cleared;
	371	+* Charge current limit to set the 'Ready to charge' – a tolerant charging current limit value, A; if the limit is //below //this level, the “Ready to charge” signal is set;
	372	+* Errors 1, 2 to clear the "Ready to charge" – bitfields to choose the errors which will clear the "Ready to charge" signal.
373	373
374	374	(% class="box infomessage" %)
375	375	(((
...	...	@@ -386,15 +386,15 @@
386	386
387	387	In this section:
388	388
389		-* **Current to set the "Discharging current present"** – a current level to generate the "Discharging current present" signal, А;
390		-* **Current to clear the "Discharging current present"** – a current level to clear the "Discharging current present" signal, А;
391		-* **Voltage to clear the “Ready to discharge”** – a threshold U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if the voltage of any cell is below this level, the “Ready to discharge” signal is cleared;
392		-* **Voltage to reset the “Ready to discharge”** – a tolerant U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if all cells voltages are above the tolerant level, the “Ready to discharge” signal is set;
393		-* **Use actual voltage to generate the "Ready to discharge" signal** – a flag to disable voltage correction for "Ready to discharge" signal;
394		-* **Treat positive currents as zero currents for generating the "Ready to discharge" signal** – a flag to disable voltage correction for "Ready to discharge" signal at charging current;
395		-* **Check the 'Discharge current limit' value to generate the 'Ready to discharge'** – a flag to enable check of "Discharging current limit" to generate the "Ready to discharge" signal;
396		-* **Discharge current limit to clear the 'Ready to discharge'** – a threshold discharging current limit value, A; if the limit is //above //this level, the “Ready to discharge” signal is cleared;
397		-* **Discharge current limit to set the 'Ready to discharge'** – a tolerant discharging current limit value, A; if the limit is //below //this level, the “Ready to discharge” signal is set;
	389	+* Current to set the "Discharging current present" – a current level to generate the "Discharging current present" signal, А;
	390	+* Current to clear the "Discharging current present" – a current level to clear the "Discharging current present" signal, А;
	391	+* Voltage to clear the “Ready to discharge” – a threshold U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if the voltage of any cell is below this level, the “Ready to discharge” signal is cleared;
	392	+* Voltage to reset the “Ready to discharge” – a tolerant U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if all cells voltages are above the tolerant level, the “Ready to discharge” signal is set;
	393	+* Use actual voltage to generate the "Ready to discharge" signal – a flag to disable voltage correction for "Ready to discharge" signal;
	394	+* Treat positive currents as zero currents for generating the "Ready to discharge" signal – a flag to disable voltage correction for "Ready to discharge" signal at charging current;
	395	+* Check the 'Discharge current limit' value to generate the 'Ready to discharge' – a flag to enable check of "Discharging current limit" to generate the "Ready to discharge" signal;
	396	+* Discharge current limit to clear the 'Ready to discharge' – a threshold discharging current limit value, A; if the limit is //above //this level, the “Ready to discharge” signal is cleared;
	397	+* Discharge current limit to set the 'Ready to discharge' – a tolerant discharging current limit value, A; if the limit is //below //this level, the “Ready to discharge” signal is set;
398	398	* Clear the 'Ready to discharge' signal if the 'Low SOC' signal is set;
399	399	* Errors 1, 2 to clear the "Ready to discharge" – bitfields to choose the errors which will clear the "Ready to discharge" signal.
400	400