Changes for page 3.3 Control

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -312,23 +312,26 @@
312	312
313	313	=== Main contactor ===
314	314
315		-The BMS Main 3 / BMS Main 2R device controls the main contactor. The main contactor is usually placed in the common (minus) battery line for opening the charge and discharge circuits in case of sealing of the charging or discharging contactors.
	315	+The BMS Main 3 / BMs device controls the main contactor. The main contactor is usually placed in the common (minus) battery line for opening the charge and discharge circuits in case of sealing of the charging or discharging contactors.
316	316
317	317	The Main contactor algorithm supports the following modes:
318	318
319		-In **“Always on”** mode main contactor closes if all the following is true:
	319	+* Always on;
	320	+* Automatic.
320	320
	322	+In “Always on” mode main contactor closes if all the following is true:
	323	+
321	321	* Other contactors are open;
322		-* There are __no errors__ from the "Errors 1, 2 ..." bitfileds.
	325	+* There are no errors from the "Errors 1, 2 ..." bitfileds.
323	323
324		-and opens if all the following is true:
	327	+In “Always on” mode main contactor opens if all the following is true:
325	325
326	326	* Other contactors are open;
327		-* There is __an error__ from the the "Errors 1, 2 ..." bitfileds.
	330	+* There is an error from the the "Errors 1, 2 ..." bitfileds.
328	328
329		-In **“Automatic”** mode, the main contactor closes by internal algorithms at the same time with other contactors.
	332	+In “Automatic” mode, the main contactor closes by internal algorithms at the same time with other contactors.
330	330
331		-In **“On demand”** mode, the main contactor closes by external the “Close Main contactor” request.
	334	+In “On demand” mode, the main contactor closes by external the “Close Main contactor” request.
332	332
333	333	(% class="box infomessage" %)
334	334	(((
...	...	@@ -341,15 +341,15 @@
341	341
342	342	In this section:
343	343
344		-* **Enable **– a flag to enable the main contactor control;
345		-* **Algorithm** – main contactor control algorithm:
346		-** **Always on** – contactor is always closed;
347		-** **Automatic** – contactor closes by internal charge and discharge algorithms;
348		-** **On demand** – contactor is closed by an external request;
349		-* **Time to keep the contactor closed before closing the others** – a time for other contactors to be open after the main contactor is closed;
350		-* **Delay before opening the contactor** – a time which is used to detect conditions for opening the contactor, s;
351		-* **Keep the contactor open until the device is restarted** – a flag for keeping the main contactor open until the system is reset;
352		-* **Errors 1, 2 to open the main contactor** – bitfields to choose the errors which will open the main contactor.
	347	+* Enable – a flag to enable the main contactor control;
	348	+* Algorithm – main contactor control algorithm:
	349	+** Always on – contactor is always closed;
	350	+** Automatic – contactor closes by internal charge and discharge algorithms;
	351	+** On demand – contactor is closed by an external request;
	352	+* Time to keep the contactor closed before closing the others – a time for other contactors to be open after the main contactor is closed;
	353	+* Delay before opening the contactor – a time which is used to detect conditions for opening the contactor, s;
	354	+* Keep the contactor open until the device is restarted – a flag for keeping the main contactor open until the system is reset;
	355	+* Errors 1, 2 to open the main contactor – bitfields to choose the errors which will open the main contactor.
353	353
354	354	=== Charging status ===
355	355
...	...	@@ -359,17 +359,17 @@
359	359
360	360	In this section:
361	361
362		-* **Current to set the "Charging current present"** – a current level to generate the "Charging current present" signal, A;
363		-* **Current to clear the "Charging current present"** – a current level to clear the "Charging current present" signal, A;
364		-* **Voltage to clear the “Ready to charge”** – a threshold U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if the voltage of any cell is above this level, the “Ready to charge” (hence, the “Allow charging”) signal is cleared;
365		-* **Voltage to reset the “Ready to charge”** – a tolerant U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if all cell voltages are below the tolerant level, the “Ready to charge” (hence, the “Allow charging”) signal is set;
366		-* **Use actual voltage to generate the "Ready to charge" signal** – a flag to disable voltage correction for "Ready to charge" signal;
367		-* **Treat negative currents as zero currents for generating the "Ready to charge" signal** – a flag to disable voltage correction for "Ready to charge" signal at discharging current;
368		-* **Delay before recharging** – a time after which the previously opened the allow charging contactor closes again, minute; to disable the operation by timeout set "Delay before recharging" to 0;
369		-* **Check the 'Charge current limit' value to generate the 'Ready to charge'** – a flag to enable check of "Charging current limit" to generate the "Ready to charge" signal;
370		-* **Charge current limit to clear the 'Ready to charge'** – a threshold charging current limit value, A; if the limit is //above //this level, the “Ready to charge” signal is cleared;
371		-* **Charge current limit to set the 'Ready to charge'** – a tolerant charging current limit value, A; if the limit is //below //this level, the “Ready to charge” signal is set;
372		-* **Errors 1, 2 to clear the "Ready to charge"** – bitfields to choose the errors which will clear the "Ready to charge" signal.
	365	+* Current to set the "Charging current present" – a current level to generate the "Charging current present" signal, A;
	366	+* Current to clear the "Charging current present" – a current level to clear the "Charging current present" signal, A;
	367	+* Voltage to clear the “Ready to charge” – a threshold U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if the voltage of any cell is above this level, the “Ready to charge” (hence, the “Allow charging”) signal is cleared;
	368	+* Voltage to reset the “Ready to charge” – a tolerant U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if all cell voltages are below the tolerant level, the “Ready to charge” (hence, the “Allow charging”) signal is set;
	369	+* Use actual voltage to generate the "Ready to charge" signal – a flag to disable voltage correction for "Ready to charge" signal;
	370	+* Treat negative currents as zero currents for generating the "Ready to charge" signal – a flag to disable voltage correction for "Ready to charge" signal at discharging current;
	371	+* Delay before recharging – a time after which the previously opened the allow charging contactor closes again, minute; to disable the operation by timeout set "Delay before recharging" to 0;
	372	+* Check the 'Charge current limit' value to generate the 'Ready to charge' – a flag to enable check of "Charging current limit" to generate the "Ready to charge" signal;
	373	+* Charge current limit to clear the 'Ready to charge' – a threshold charging current limit value, A; if the limit is //above //this level, the “Ready to charge” signal is cleared;
	374	+* Charge current limit to set the 'Ready to charge' – a tolerant charging current limit value, A; if the limit is //below //this level, the “Ready to charge” signal is set;
	375	+* Errors 1, 2 to clear the "Ready to charge" – bitfields to choose the errors which will clear the "Ready to charge" signal.
373	373
374	374	(% class="box infomessage" %)
375	375	(((
...	...	@@ -386,15 +386,15 @@
386	386
387	387	In this section:
388	388
389		-* **Current to set the "Discharging current present"** – a current level to generate the "Discharging current present" signal, А;
390		-* **Current to clear the "Discharging current present"** – a current level to clear the "Discharging current present" signal, А;
391		-* **Voltage to clear the “Ready to discharge”** – a threshold U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if the voltage of any cell is below this level, the “Ready to discharge” signal is cleared;
392		-* **Voltage to reset the “Ready to discharge”** – a tolerant U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if all cells voltages are above the tolerant level, the “Ready to discharge” signal is set;
393		-* **Use actual voltage to generate the "Ready to discharge" signal** – a flag to disable voltage correction for "Ready to discharge" signal;
394		-* **Treat positive currents as zero currents for generating the "Ready to discharge" signal** – a flag to disable voltage correction for "Ready to discharge" signal at charging current;
395		-* **Check the 'Discharge current limit' value to generate the 'Ready to discharge'** – a flag to enable check of "Discharging current limit" to generate the "Ready to discharge" signal;
396		-* **Discharge current limit to clear the 'Ready to discharge'** – a threshold discharging current limit value, A; if the limit is //above //this level, the “Ready to discharge” signal is cleared;
397		-* **Discharge current limit to set the 'Ready to discharge'** – a tolerant discharging current limit value, A; if the limit is //below //this level, the “Ready to discharge” signal is set;
	392	+* Current to set the "Discharging current present" – a current level to generate the "Discharging current present" signal, А;
	393	+* Current to clear the "Discharging current present" – a current level to clear the "Discharging current present" signal, А;
	394	+* Voltage to clear the “Ready to discharge” – a threshold U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if the voltage of any cell is below this level, the “Ready to discharge” signal is cleared;
	395	+* Voltage to reset the “Ready to discharge” – a tolerant U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if all cells voltages are above the tolerant level, the “Ready to discharge” signal is set;
	396	+* Use actual voltage to generate the "Ready to discharge" signal – a flag to disable voltage correction for "Ready to discharge" signal;
	397	+* Treat positive currents as zero currents for generating the "Ready to discharge" signal – a flag to disable voltage correction for "Ready to discharge" signal at charging current;
	398	+* Check the 'Discharge current limit' value to generate the 'Ready to discharge' – a flag to enable check of "Discharging current limit" to generate the "Ready to discharge" signal;
	399	+* Discharge current limit to clear the 'Ready to discharge' – a threshold discharging current limit value, A; if the limit is //above //this level, the “Ready to discharge” signal is cleared;
	400	+* Discharge current limit to set the 'Ready to discharge' – a tolerant discharging current limit value, A; if the limit is //below //this level, the “Ready to discharge” signal is set;
398	398	* Clear the 'Ready to discharge' signal if the 'Low SOC' signal is set;
399	399	* Errors 1, 2 to clear the "Ready to discharge" – bitfields to choose the errors which will clear the "Ready to discharge" signal.
400	400