Changes for page 3.3 Control

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -12,27 +12,31 @@
12	12
13	13	In this section:
14	14
15		-* Cell capacity – nominal capacity of cells, Ah;
16		-* Cell resistance – nominal (maximum) internal resistance of the cells, Ohm;
17		-* Relax time (after charging) – a relaxation time after charging, second;
18		-* Relax time (atfer discharging) – a relaxation time after discharging, second;
19		-* Reset parameters – a command to reset cells state of charge, capacity, and resistance;
20		-* Method of calculating the battery voltage:
21		-** Summation of cell voltages – the overall voltage is calculated as on sum of all cells in the battery;
22		-** Using voltage before contactors – the overall voltage is estimated as voltage before contactors measured by BMS.
	15	+* **Cell capacity** – nominal capacity of cells, Ah;
	16	+* **Cell resistance** – nominal (maximum) internal resistance of the cells, Ohm;
	17	+* **Connection of cells:**
	18	+** **Serial **– all cells are connected in series in a single string.
	19	+** **Parallel-Serial **– cells are grouped in parallel and serial items;
	20	+* **Parallel-Serial: Number of Logic devices in a chain**;
	21	+* **Parallel-Serial: Number of parallel chains in a block**;
	22	+* **Parallel-Serial: Number of serial blocks in a string**;
	23	+* **Relax time (after charging)** – a relaxation time after charging, second;
	24	+* **Relax time (atfer discharging)** – a relaxation time after discharging, second;
	25	+* **Reset SOC** – a command to reset cells state of charge. New cell SOC values will be calculated based on cell voltage and “Uocv (open-circuit voltage) table”: in the “Control → SOC estimation” section;
	26	+* **Reset resistance** – a command to reset cells resistance to “Cell resistance” value;
	27	+* **Reset capacity** – a command to reset cells capacity to “Cell capacity” value;
	28	+* **Method of calculating the battery voltage***:
	29	+** **Summation of cell voltages** – the overall voltage is calculated as on sum of all cells in the battery;
	30	+** **Using voltage before contactors** – the overall voltage is estimated as voltage before contactors measured by BMS.
23	23
24		-The values “Capacity” and “Resistance” are used to calculate the SOC of cells and the battery.
	32	+The **"Parallel-Serial"** connection works as follows: a bunch of serial connected Logics are grouped into chains. A bunch of parallel connected chains are grouped to blocks. A bunch of serial connected blocks are grouped into string. By configuring the corresponding settings it is possible to create a complex string configuration. Current through each chain will be estimated as a fraction of overall current accordingly to the number of chains in a block.
25	25
26		-The values of “Relax time” are used to determine the state of the battery. If the battery is in a state of relaxation, the system recalculates the voltage on the cells to the state of charge of the battery.
	34	+The values **“Capacity”** and **“Resistance”** are used to calculate the SOC of cells and the battery.
27	27
28		-The “Reset parameters” will reset:
	36	+The values of **“Relax time”** are used to determine the state of the battery. If the battery is in a state of relaxation, the system recalculates the voltage on the cells to the state of charge of the battery.
29	29
30		-* state of charge (new cell SOC values will be calculated based on cell voltage and “Uocv (open-circuit voltage) table”: in the “Control → SOC estimation” section);
31		-* cell resistance to “Cell resistance” value;
32		-* battery capacity to “Cell capacity” value.
	38	+The **“Reset ”** command is used for starting-up and adjustment of the battery.
33	33
34		-The “Reset parameters” command is used for starting-up and adjustment of the battery.
35		-
36	36	=== SOC estimation ===
37	37
38	38	The BMS Main 3 device calculates the state of charge of the battery (SOC) using two algorithms: