Skip to Content

Changes for page 3.3 Control

Last modified by Admin on 2026/04/30 15:56
From version 73.1
edited by Admin
on 2026/02/18 16:19
Change comment: There is no comment for this version
To version 66.4
edited by Admin
on 2025/12/11 10:04
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -106,23 +106,13 @@
106 106  
107 107  The BMS Main 3 device calculates the state of health of the battery (SOH) using two algorithms:
108 108  
109 -* By effective capacity;
110 -* By total charge-.
109 +* by effective capacity;
110 +* by total charge-.
111 111  
112 -In "By effective capacity" mode SOH is calculated as a ratio of effective capacity to nominal capacity. Effective capacity is estimated to DOD value when battery SOC reaches 0%, so SOH is recalculated each full battery discharge.
112 +In "By effective capacity" mode SOH is calculated as a ratio of effective capacity to nominal capacity.
113 113  
114 -In "By total charge-" mode SOH is calculated as a linear function of "Total charge-" counter. While "Total charge-" constantly increases during battery operation, SOH will be linearly decrease at the same time. This mode requires a confirmed data about cell health depending of amount of discharge rate to configure the linear function.
114 +In "By total charge-" mode SOH is calculated as a
115 115  
116 -To configure parameters for battery state of health calculation, select the "Control → SOH correction" section:
117 -
118 -[[image:1765447975228-766.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="96" width="800"]]In this section:
119 -
120 -* Algorithm:
121 -** By effective capacity;
122 -** By total charge-;
123 -* Total charge: Charge- –  total amount of charge- for expected SOH;
124 -* Total charge: SOH –  expected SOH value at the total amount of charge-.
125 -
126 126  === Resistance estimation ===
127 127  
128 128  Calculation of the resistance of cells is carried out in two ways. The first method is used when the battery passes from a relaxation state to a charge or discharge state, wherein the cell resistance value
... ... @@ -403,7 +403,7 @@
403 403  
404 404  To change the parameters of discharging process status, select the "Control → Discharging status" section:
405 405  
406 -[[image:1771431570393-551.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="155" width="800"]]
396 +[[image:1760435802140-274.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="129" width="800"]]
407 407  
408 408  In this section:
409 409  
... ... @@ -415,7 +415,6 @@
415 415  * Check the 'Discharge current limit' value to generate the 'Ready to discharge' – a flag to enable check of "Discharging current limit" to generate the "Ready to discharge" signal;
416 416  * Discharge current limit to clear the 'Ready to discharge' – a threshold discharging current limit value, A; if the limit is //above //this level, the “Ready to discharge” signal is cleared;
417 417  * Discharge current limit to set the 'Ready to discharge' – a tolerant discharging current limit value, A; if the limit is //below //this level, the “Ready to discharge” signal is set;
418 -* Clear the 'Ready to discharge' signal if the 'Low SOC' signal is set;
419 419  * Errors 1, 2 to clear the "Ready to discharge" – bitfields to choose the errors which will clear the "Ready to discharge" signal.
420 420  
421 421  === Precharge ===
1765447975228-766.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -18.8 KB
Content
1765448283865-334.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -20.9 KB
Content
1771431551882-439.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -43.7 KB
Content
1771431570393-551.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -43.7 KB
Content